background image

LAUNCH  

Installation Instruction for Economical Symmetric Floor-plate 2-post Lift

 

1 Precaution 

Warning 

 

 

z

 

This manual is an essential integral part of this 
equipment. Please read it carefully. 

z

 

Properly keep this manual for use during the 
maintenance. 

z

 

This lift is only used for its clearly designated purpose. 
Never use it for other purposes. 

z

 

The manufacturer is not responsible for any damage 
or injury caused by improper use or use for other 
purposes. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Precautions for the Installation 

and Adjustment:

 

z

 

Before the installation and adjustment, carefully read 
this manual and the user’s manual. Without the 
permission of the manufacturer or not following the 
requirement of the manual, any changes on the 
machine parts and its usage may cause direct or 
indirect damage to the machine and injury on 
operators.  

z

 

To do the installation and adjustment, the personnel 
must have certain electrical knowledge. 

z

 

The operators must undergo special training and are 
qualified. 

z

 

Fix and install the lift on the stable concreted floor. 

z

 

The lift shall be installed in a sufficient space so that 
the operation is not restricted. 

z

 

Don’t expose the lift to the extreme temperature and 
humidity environment. Avoid installation beside the 
heating equipment, water tap, air humidifier or stove. 

z

 

Don’t install the lift in front of the window where the 
sunlight can shine directly. When it’s unavoidable, use 
curtain to shield the sunlight. 

z

 

The manufacturer reserves the right to make design 
changes or add improvements to its product line 
without notice. 

z

 

Before installation, carefully check the packing list of 
lift. In case of any question, please contact the 
distributor or LAUNCH immediately. 

 
 
 
 
 
 
 
 
 
 
 

 

 

 

Summary of Contents for TLT235SB


















Reviews: