background image

LAUNCH  

                                                                                                                                           

 TLT830WA Product Manual

 

Copyright reserved! Without the written agreement of 

Launch Shanghai Machinery Co., Ltd. (hereinafter 

called “Launch”), no company or individual is 

allowed to copy and backup this manual in any form 

(electronic, mechanical, photocopy, recording or other 

forms). This manual is specifically designed for the 

use of Launch product, and our company doesn’t 

undertake any responsibility for various consequences 

caused as a result of applying it to the guidance of 

operating other equipment. 

 

In case of the equipment damage or loss due to the 

accident of the user himself or third party, abuse or 

misuse of this equipment, unauthorized change and 

repair of this equipment, or not conforming to the 

operation and maintenance requirement of Launch, 

Launch and its branches won’t undertake any 

responsibility for the expenses and expenditures 

generated. 

 

For the equipment damage or problem caused as a 

result of using other optional accessories or 

consumables instead of original Launch product or its 

recognized product, Launch won’t undertake any 

responsibility. 

Official statement: The purpose of other- product- 

names mentioned in this manual is to describe how to 

use this equipment. Their registered trademarks still 

belong to the original companies. 

 

 

This equipment is for the use of professional technical 

personnel or maintenance personnel. 

 

Registered Trademark 

Launch has registered its trademark in China and 

several foreign countries, with the symbol of 

LAUNCH. Other trademarks, service symbol, domain 

name, icon, and company name of Launch mentioned 

in this manual belong to the property of Launch and 

its subsidiary companies. In the countries where 

Launch’s trademark, service symbol, domain name, 

icon and company name haven’t been registered, 

Launch declares its ownership on such unregistered 

trademark, service symbol, domain name, icon and 

company name. The trademarks of other products and 

company names mentioned in this manual still belong 

to the originally registered companies. Without prior 

written agreement of the owner, nobody can use the 

trademark, service symbol, domain name, icon and 

company name of Launch and other companies 

mentioned in this manual. If you have any question, 

please visit website of Launch: 

http://www.cnlaunch.com or write to Sales Dept. of 

Launch Shanghai Machinery Co., Ltd. at No. 661 

Baian Road, International Automobile City Auxiliary 

Parts Park, Anting Town, Jiading District, Shanghai 

City to contact Launch 

   

 

The product consists of the People's Insurance 
Company underwriting 

Summary of Contents for TLT830WA



































Reviews: