background image

LAUNCH   

Tire Changer TWC-481

1

Safety Precautions

This  manual  is  a  necessary  part  of  the  product.   
Please review carefully. 

Keep  the  manual  for  later  use  when  maintaining 
the machine. 

This machine can only be used for the designated 
purpose.    Never use it for any other purpose. 

The  manufacturer  is  not  responsible  for  any 
damage  incurred  by  improper  use  or  use  for  the 
purposes other than the intended one. 

Before  installing  and  adjusting  the  equipment,  pay 
attention to the following: 

Read this manual and all other instructions for the 
equipment  thoroughly.    Modification  to  any 
components or parts, or use the machine for other 
purpose  without  either  obtaining  the  permission 
from the producer, or observing the requirement of 
the  instructions  may  lead  to  direct  or  indirect 
damage to the equipment.   

The installation and maintenance personnel should 
have a good understanding of electrical devices. 

The  equipment  can  only  be  operated  by  qualified 
personnel with special training. 

TWC-481 should be installed on the stable ground. 

Keep  the back panel 0.5M  away from  the wall for 
good ventilation.    Enough room should be left on 
both sides of TWC-481 for convenient operation. 

Do  not  put  TWC-481  in  a  place  with  high 
temperature  or  moisture,  or  near  the  heating 
system, water tap, air-humidifier or furnace.   

Do  not  install  TWC-481  near  a  window  with 
sunlight.    Protect the unit  with a curtain or shield 
if necessary. 

Go  through  the  accessory  list  carefully  before 
installation.    Should  there  be  any  questions 
please contact your agent or Launch Tech Co., Ltd.   

Summary of Contents for TWC-481



























Reviews:

Related manuals for TWC-481