background image

LAUNCH

Tire Changer TWC-581

3

Safety Precautions 

This manual is a necessary component of the product.    Please review carefully. 

Keep the manual for later use when maintaining the machine. 

This machine can only be used for the designed purpose.    Never use it for any other purpose. 

The manufacturer is not held responsible for any damage incurred by improper use or use for the purposes other 
than the intended one. 

Before installing and adjusting the equipment, pay attention to the following

 

Read this manual and all other instructions for the equipment thoroughly.    Modification to any components or 
parts,  or  use  the machine  for other  purpose  without  either  obtaining  the  permission  from  the manufacturer,  or 
observing the requirement of the instructions may lead to direct or indirect damage to the equipment.   

The installation and adjusting personnel should have a good understanding of electrical devices. 

The equipment can only be operated by qualified personnel with special training. 

TWC-581 should be installed on the smooth ground. 

Keep the back panel 0.75M (29”) away from the wall for good ventilation. Enough room should be left on both 
sides of TWC-581 for convenient operation. 

Do  expose  the  TWC-581  to  high  temperature  or  moisture,  or  position  near  a  heating  system,  water  tap, 
air-humidifier or furnace.   

Do not install TWC-581 near a window with direct sunlight.    Protect the unit with a curtain or shade if necessary. 

Go through the accessory list carefully before installation.    Should there be any questions please contact your 
Rep. or Launch Tech USA Inc. 

Summary of Contents for TWC-581

































Reviews:

Related manuals for TWC-581