background image

LAUNCH

 

                               

X-431 EURO TAB II User Manual

 

88 

11 FAQ

 

1. Communication error with vehicle ECU? 

Please confirm: 

1.  Whether the VCI is properly connected. 

2.  Whether the vehicle ignition switch is ON. 

3.  If all checks are normal, send vehicle year, make, model and VIN number to 

us using Feedback feature. 

2. Failed to enter into vehicle ECU system? 

Please confirm: 

1.  Whether the vehicle is equipped with the system. 

2.  Whether the VCI is correctly connected. 

3.  Whether the vehicle ignition switch is ON. 

4.  If all checks are normal, send vehicle year, make, model and VIN number t o 

us using Feedback feature. 

3.  Can  I  use  any  other  power  adaptor  other  than  the  included  power 

adaptor to charge the handset?

 

No.  Please  use  only  the  included  power  adaptor  to  charge  the  handset.  We 

assume  no  responsibility  for  damage  or  loss  resulting  fr om  the  use  of  the  any 

other adaptors. 

4. How to save power? 

  Please turn off the screen while the device keeps idle. 

  Set a shorter standby time. 

  Decrease the brightness of the screen. 

  If WLAN connection is not required, please turn it off. 

  Disable GPS function if GPS service is not in use. 

5. How to reset the tablet? 

*Warning: Resetting may cause data loss. Before doing so, please make sure important 

data and information has been backed up. 

Summary of Contents for X-431 EURO TAB II






























































































Reviews: