background image

Safety 

& Accessory

Initial Use

Diagnostics

FAQ & Care

Product Profile

36

www.x431.com    +86 755 8455 7891 

LAUNCH      

                                                                                            

PAD VII

 

User Manual

to shift delay or impact problem. In this case, this function needs to be done so that the gearbox can 

automatically compensate according to the driving conditions so as to achieve more comfortable and 

better shift quality.

6.13 AFS (Adaptive Front-lighting System) Reset 

This feature is used to initialize the adaptive headlamp system. According to the ambient light intensity, the 

adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust 

the headlamp lighting angle while monitoring the vehicle speed and body posture.

6.14 Sunroof Initialization

This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, 

temperature threshold outside the car etc.

6.15 Suspension Calibration 

1. This function can adjust the height of the body. 
2. When replacing the body height sensor in the air suspension system, or control module or when the 

vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level 

calibration.

6.16 EgR Adaption

This function is used to learn the Egr (Exhaust gas recirculation) valve after it is cleaned or replaced.

6.17 Seats Calibration

This function is applied to match the seats with memory function that are replaced and repaired.

6.18 Tyre Reset

This function is used to set the size parameters of the modified or replaced tire.

6.19 Coolant Bleed 

Use this function to activate the electronic water pump before venting the cooling system.

6.20 AdBlue Reset (Diesel Engine Exhaust gas Filter)

After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.

6.21 NOx Sensor Reset

NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. If the 

NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic 

converter learned value stored in the engine ECU.

Summary of Contents for X-431 PAD VI


















































































Reviews: