17
ASSEMBLY
In the case that two islands are too close, the width between two islands no more than 1m, it is
recommended to lay out the boundary wire as illustrated (Fig. 15).
How to wire a sub zone
,IWKHUHDUHDGGLWLRQDO]RQHVLQ\RXUODZQ
Ŷ7RDOORZWKHPRZHUWRGULYHWKURXJKWKHQDUURZSDVVDJHVPRRWKO\WKHQDUURZSDVVDJHWKDW
FRQQHFWVWKHPDLQ]RQHDQGVXE]RQHVKRXOGEHDWOHDVWPZLGHDQGDWPRVWPORQJ)LJ
16).
Ŷ0DNHVXUHWKHQDUURZSDVVDJHLV¿UPOHYHODQGVPRRWK
Ŷ,IWKHQDUURZSDVVDJHWKDWFRQQHFWVWZRDUHDVLVWRRQDUURZIRUWKHURERWLFODZQPRZHUWR
QDYLJDWHOD\WKHERXQGDU\ZLUHDURXQGWKHVXE]RQHVRWKDWLWIRUPVDQLVODQGRXWVLGHRIWKH
PDLQ]RQH)LJ&DUU\WKHPRZHUPDQXDOO\WRWKHVXE]RQH7KHPRZHUZLOOPRZXQWLOWKH
EDWWHU\UXQVRXW7KHQWDNHWKHPRZHUEDFNWRWKHEDVHVWDWLRQLQWKHPDLQ]RQHIRUUHFKDUJH
Connect and Install the Base Station (See Figs. 18-22)
NOTE:
Start at the base station’s location to lay the boundary wire anti-clockwise around the lawn.
NOTE:
The boundary wire must be laid and connected to the base station before securing the
base station to the ground.
Ŷ3ODFHWKHEDVHVWDWLRQRQWKHJURXQGLQWKHGHVLUHGSRVLWLRQ)ROORZWKHLQVWUXFWLRQVLQWKH³6HOHFW
WKH3URSHU%DVH6WDWLRQ/RFDWLRQ´VHFWLRQ'RQRWFRQQHFWWKHEDVHVWDWLRQWRWKHPDLQVRU¿[
into place.
Ŷ3HJWKHVWDUWLQJHQGRIWKHERXQGDU\ZLUHLQWRSODFHDWSRVLWLRQDVLOOXVWUDWHGFORVHWRWKH
terminals at the rear of the base station), leaving 20cm length for connection later (Fig. 18).
Ŷ,QVWDOOWKHERXQGDU\ZLUHDQWLFORFNZLVHDURXQGWKHODZQDVGHVFULEHGLQWKH³/D\WKH%RXQGDU\
:LUH´VHFWLRQ
Ŷ5XQWKHHQGRIWKHERXQGDU\ZLUHWKURXJKWKHVORWXQGHUWKHEDVHVWDWLRQOHDYLQJFP
length for connection later (Fig. 18).
Ŷ:LWKWKHZLUHVWULSSHUSURYLGHGVWULSPPRILQVXODWLRQPDWHULDOIURPWKHHQGVRIWKH
boundary wire for connection to the base station (Fig. 19).
Ŷ%HIRUHFRQQHFWLQJWKHERXQGDU\ZLUHWRWKHEDVHVWDWLRQHQVXUHWKHEDVHVWDWLRQSRZHUVXSSO\
is disconnected from the mains.
Ŷ,QVHUWWKHZLUHHQGVLQWRWHUPLQDOVDWWKHUHDURIWKHEDVHVWDWLRQ5XQWKHVWDUWLQJZLUH
through the hook (C) of the base station and connect it to the red terminal (A). The end of the
wire ( ) that runs under the base station connects to the black terminal (B). To insert the wire
end into the terminal, press down on the tab of the terminal until the terminal hole is visible, fully
insert the wire end into the corresponding terminal, and then release the tab to secure the wire
HQG*HQWO\SXOOWKHZLUHVRQFHWKH\DUHFRQQHFWHGDQGPDNHVXUHWKH\DUHFRQQHFWHG¿UPO\
into place. This is important to ensure correct signal of the boundary wire (Fig. 20).
1
1
2
2
