background image

Anleitung/Manual

Lazy Camping – Lazy Tent

Thank you for choosing a Lazy Tent from Lazy Camping.

Before you begin, take a moment to familiarize yourself with these instructions and the parts included.

On page 2 you will find a list of all parts, quantities and tools needed.

Please read first

Important notes

It is essential that all Lazy Camping products are properly and securely mounted and attached to your 

vehicle. Improper attachment can result in an accident and cause serious bodily injury or death. You are 

responsible for mounting and securing all Lazy Camping products to your vehicle. Attachments must be 

inspected before use and products must be checked regularly for adjustment, wear and damage. Therefore, 

you must read and understand all instructions and cautions before mounting or using Lazy Camping 

products. If you do not understand all the instructions and cautions, or if you have no manual experience 

and you are not thoroughly familiar with the assembly procedures, you should have the product installed 

by a professional assembler or other qualified persons.

120 

Minutes

Persons

Ausführliches YouTube Video 

zum 

Lazy Tent – Aufbau

Summary of Contents for Lazy Tent



















Reviews: