background image

GB-15

D

GB

F

NL

I

E

Ceramic radiant tube SER-C

  Burner seal

  Flange connection

  Radiant tube (SiSiC)

4

  Mounting gasket

For heat treatment processes in which combustion 
gases must be kept separate from the product. The 
patented flange connection is gas-tight.
Material: SiSiC, max. application temperature: 

1300°C.
The SER-C is not supplied with the ECOMAX

®

 and 

must be ordered separately.

Flue gas guide tube FGT

To guide the flue gases if smaller burners are used 

than those normally intended.
Material: vacuum moulded pulp.

Available on request in different sizes suitable for the 

SER-C radiant tube and ECOMAX

®

 burner sizes.

Segmented flame tube SICAFLEX

®

Segmented ceramic flame tubes to guide hot flue 
gases in radiant tubes.
Material: SiSiC.

The SICAFLEX

®

 is not supplied with the ECOMAX

®

 

and must be ordered separately.

P/P set Eco

Nozzle to limit the volume of purging air in order to 
achieve safe ignition and monitoring of the ECOMAX

®

 

burner and to avoid condensation and overheating.

Nozzle*

Order number

P2 set Eco 2.5 /E

22801111

P2 set Eco 4.0 /E

22801108

P3 set Eco 2.5 /B

22801107

P3 set Eco 4.0 /B

22801106

Technical data

Heating: direct with eductor or indirect in radiant 
tube.
Control type: On/Off.
Control range: approx. 1:3.
Flame velocity: approx. 120 to 150 m/s.
Flame control: direct ionization control (UV control 
as an option).
Ignition: direct spark ignition.
Recuperator: 
ECOMAX

®

..C:  

ceramic (SiSiC), max. application temperature: 

1250°C, 

ECOMAX

®

..M: 

cast steel, max. application temperature: 1150°C, 
ECOMAX

®

..FTR: 

metallic, max. application temperature: 1050°C.
Storage temperature: -20°C to +40°C.

Burner

Capacity [kW] Flame length [mm]*

ECOMAX

®

 0

25

250

ECOMAX

®

 1

36

350

ECOMAX

®

 2

60

450

ECOMAX

®

 3

100

600

ECOMAX

®

 4

180

800

ECOMAX

®

 5

250

800

ECOMAX

®

 6

500

800

*  Visible range for natural gas operation in the open air, 

max. connection rating and air index 1.15.

 WARNING

Information pursuant to REACH Regulation No. 

1907/2006, Article 33.

Insulation contains refractory ceramic fibres (RCF)/
aluminium silicate wool (ASW).
RCF/ASW are listed in the Candidate List of the 
European REACH Regulation No. 1907/2006.

 

Information on the safe handling of products 
containing ceramic fibres can be found in the 
safety data sheets.

 

Safety data sheets are available on request.

Summary of Contents for ECOMAX 0



















Reviews: