-2-
UDOS 51E
–
Operator’s
Manual v1.6
P
rior to using, read, understand
and follow all safety warnings,
cautions, instructions, and specifications provided with
this power tool.
Failure to follow all of the instructions
provided with this power tool may result in significant
property damage, personal injury, or death.
Do not operate the tool in the
presence of flammable vapors,
gases, liquids or dust.
Powered tools may create sparks
at any time the tool plugged into a power source,
potentially resulting in an explosion.
Work in a neat, clean and well-lit area.
Clutter and dimly
lit areas can result in accidents.
Keep bystanders away during operation.
Proper personal
protective equipment must be worn by the tool operator
and any bystanders.
This tool must be plugged into
an outlet that exactly matches
the plug provided with the tool. NEVER MODIFY THE
POWER PLUG.
Confirm the outlet and circuit providing
power to the tool is of sufficient capacity.
Do NOT expose or operate the tool in wet conditions.
Water entering the tool, or standing in or near water
while the tool is plugged in, greatly increases the risk of
electric shock.
Do NOT abuse the power cord.
Never carry, swing, or
drag the tool by the power cord. DO NOT unplug the tool
by pulling on the power cord.
Inspect the power cord for any damage or degradation
such as cracks, splits, and swelling prior to use.
Using the
tool with a damaged or degraded cord increases the risk
of electric shock.
The use of Ground Fault Circuit Interrupter (GFCI)
protected power source is recommended.
A GFCI circuit
reduces the risk of electric shock.
Do NOT use this tool if you are
tired, or under the influence of
drugs, medications, or alcohol.
Operating the tool while
impaired can result in serious personal injury or death.
Use Personal Protective Equipment (PPE).
Always wear
ANSI Z87.1 protective eyewear and hearing protection
when using the tool.
Additional PPE such as non-skid
safety shoes, vibration reduction gloves, particulate mask,
respirator, and a hardhat used when conditions indicate,
can greatly reduce the risk of personal injury.
Never carry the tool with you finger on or near the
trigger.
Unintentional starting of the tool can result in
personal injury. Always confirm the trigger is in the off
(non-locked) position when plugging the tool into a power
source.
Dress properly. Do NOT wear loose fitting clothing, or
jewelry while operating the tool. Tie back long hair.
Loose clothing, jewelry, and hair can very quickly become
caught in the moving parts of the tool.
Do NOT overreach with the tool. Never operate the tool
with one hand.
Always maintain proper control of the
tool by using both hands. Losing control of the tool can
result in serious personal injury.
Do NOT overload the tool.
Select the proper size tool and
accessories for the job. Failure to do so can damage the
tool and result in an unsafe work condition.
Inspect the tool before use.
Ensure the power switch
operates correctly, the power cord is in good condition,
and the mode adjustment mechanism is operating
smoothly.
Use only specified accessories.
The use of unspecified
accessories may compromise performance, possibly
result in an unsafe work condition, and will void the
warranty.
This power tool is a combination Dual Action and Rotary
Polisher/Sander. It is intended for use in finish
correction of painted and gel-coated surfaces.
Failure to
adhere to the following instructions may result in
significant property damage, serious personal injury, or
death.
Operations such as sawing,
grinding, wire brushing, or
cutting-off are not authorized.
Performing operations for
which a tool is not designed may result in an unsafe work
condition.
Use only accessories recommended for this power tool.
Use of non-authorized accessories will result in
substandard performance and may lead to an unsafe
work condition.
Wear
personal
protective
equipment.
Depending on the
application, use a face shield, with safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask or
respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
Inspect tool and accessories
before use.
The use of damaged,
cracked, or otherwise compromised accessories can
result in breakage and thrown hi-speed fragments. After
inspecting and installing an accessory, in an area free of
bystanders, with rotating plane of the tool pointed away,
run the tool at its maximum speed for one minute to
confirm proper operation. If any thrown fragments, or
excessive imbalance is encountered, immediately stop
the tool and inspect the tool and accessories thoroughly.
GENERAL SAFETY WARNINGS
MAINTAIN A SAFE WORK AREA
ELECTRICAL SAFETY
OPERATOR SAFETY
USE AND CARE
OPERATIONAL SAFETY
OPERATIONAL SAFETY
