-3-
UDOS 51E
–
Operator’s
Manual v1.6
Do NOT cover the cooling vents
with
your
hand
during
operation.
Obstructed vents can lead to motor
overheating, resulting a thermal shutdown and potential
tool damage.
Beware
of
tool
kickback.
Kickback is a result of misuse and
can occur when tool rotation is suddenly stopped by an
obstruction. A strong opposite direction reaction torque
is then transmitted through the tool body to the operator.
This can cause serious personal injury. To avoid kickback
avoid using the tool in areas where the rotating
accessories can become caught or pinched, such as
around mirrors, antennas, panel gaps and sharp contours.
The secure use of both hands on the tool in the designed
positions will minimized the risk of personal injury if
kickback occurs. Never use one hand to operate the tool.
Do not allow any loose portion
of a polishing bonnet or its
attachment strings to spin freely.
Tuck away or trim any
loose attachment strings. Loose and spinning attachment
strings can entangle your fingers resulting in a severe
laceration or even amputation. Loose attachment strings
can snag on the workpiece resulting in kickback.
Position the cord clear of the spinning accessory.
If you
lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
Never lay the power tool down until the accessory has
come to a complete stop.
The spinning accessory may
grab the surface and pull the power tool out of your
control.
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body
❶
Trigger
❽
Front Support Bumper
❷
Trigger Lock
❾
Front Handle
❸
Rear Handle
❿
Adjustment Collar
❹
Power Cord and Strain Relief
⓫
Hub
❺
Speed Control Dial
⓬
UDOS Backing Plate
❻
Motor Vents
⓭
Stall-Aware®
❼
Rear Support Bumper
Stock Number:
51E
Input Voltage:
120 VAC
Input Frequency:
60Hz
Motor Power:
1200W
Rated RPM:
1000-2400
Backing Plate Diameter:
5”
Pad Diameter:
5 7/8”
Functions:
Rotary, Sand(8mm),
12mm, 15mm, 21mm
If an extension cord is used,
ensure the extension cord gauge
is adequate for the tool.
The UDOS tool is double
insulated thus the use of both 2 and 3 conductor
extension cords
is permitted.
If the standard UDOS power
cord is not long enough for the application, use the
following table to determine the appropriate length and
gauge extension to use.
UDOS MINIMUM EXTENSION CORD WIRE GAUGE
REQUIRED
Extension Cord Length
25 feet
50 feet
75 feet
100 feet
150 feet
16Ga.
14Ga.
12Ga.
10Ga.
n/r
n/r
–
Not Recommended
To reduce the risk of injury,
always unplug tool before
changing or removing accessories. Only use accessories
specifically recommended for this tool. Others may be
hazardous.
It is strongly recommended that you retain the packaging
in the event the tool needs to be sent to the Service
Center for repair.
Backing Plate and Pad Installation
1)
Unplug the tool, and place it on its back with the
spindle facing up.
2)
Mount the backing plate to the spindle engaging the
flats on the spindle to the mating feature on the
backing plate.
3)
Install the 8mm backing plate washer and screw.
4)
Confirm the backing plate is properly seated on the
spindle. Torque to 15 ft-lb (20N-m).
5)
Center and mount a UDOS pad to the hook & loop face
of the backing plate
OPERATIONAL SAFETY (CONT
’D)
FUNCTIONAL DEPICTION
SPECIFICATIONS
EXTENSION CORDS
ASSEMBLY
