RÜCK
Seite:
38
INSERTS (MONOKANÄLE)
In jedem monophonen MIC-Kanal steht ein Insert zur Verfügung. Über den Stereoklinkenanschluss des Inserts
können Sie externe Signalprozessoren in den Signalweg einschleifen: Dabei wird das Signal hinter dem Gain-
Regler (TRIM) abgegriffen und kann nun über einen externen Prozessor, z. B. einen Kompressor-Limiter, geführt
werden, bevor es direkt vor der EQ-Sektion wieder in den Signalfluss eingespeist wird.
Anmerkung: Für die Nutzung des Inserts wird ein spezielles Stereo-Split-Kabel (Y-Kabel) benötigt, bei dem die
Spitze des Steckers das Send- und der Ring das Return-Signal führt.
39
ALT OUTPUT
Diese 6,3 mm Klinkenbuchsen sind als unsymmetrische Ausgänge ausgeführt. Der maximale Ausgangspegel
liegt bei +22 dBu. Der Signalpegel für den ALT OUTPUT wird über den Fader ALT 3-4 auf der Vorderseite ausge
-
steuert.
40
CTRL ROOM OUTPUT
Über diese 6,3 mm Klinkenbuchsen wird das Control-Room-Signal auf die Studiomonitorlautsprecher
oder eine zusätzliche PA-Anlage gespeist.
41
MAIN MIX OUTPUT
Dieser Stereoausgang ist sowohl mit XLR- als auch mit 6,3 mm Stereoklinkenbuchsen ausgeführt und speist das
Audiosignal auf einen Verstärker. Über die Fader MAIN MIX LEVEL können Sie den Pegel im Bereich von - ∞ bis
+10 dB aussteuern.
42
FOOT SW
Diese Buchse dient zum Anschluss eines externen Fußschalters, mit dem sich das integrierte DSP-Effekt-Modul
bequem aktivieren/deaktivieren lässt. Die Funktion entspricht der Taste DFX MUTE.
43
POWER-SCHALTER
Mit diesem Schalter schalten Sie die Stromversorgung ein (oN) und aus (oFF).
44
PHANTOM-SCHALTER
Mit diesem Schalter aktivieren Sie die +48 Volt Phantomspeisung für die 8 XLR-Mikrofoneingänge. Schließen Sie
in keinem Fall Mikrofone an, wenn die phantomspeisung bereits aktiv ist.
45
AC INPUT (Netzbuchse)
An dieser Buchse schließen Sie das Netzkabel an.
POWER
ON
OFF
PHANTOM
INSERT
INSERT
INSERT
INSERT
LEFT
RIGHT
MAIN MIX OUTPUT(BAL/UNBAL)
R
ALT OUTPUT
CTRL ROOM
OUTPUT
RIGHT(4)
LEFT
RIGHT
7
8
5
6
L
LEFT(3)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
REPLACE WITH THE SAME TYPE FUSE AND RATING
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
WARNING: SHOCK HAZARD
AVIS: RISQUE DE CHOC ELECTRIQUE
- DO NOT OPEN
- NE PAS OUVRIR
SERIAL
MODEL
Apparaten skall anslutas
till jordat uttag nar den
ansluts till ett natverk
INSERT
INSERT
INSERT
INSERT
3
4
1
2
INSERT
INSERT
INSERT
INSERT
11
12
9
10
AC INPUT
100-240V 50/60Hz
ǡ
POWER CONSUMPTION: 40W
Fuse:T1.6AL 250V
43
45
41
40 39
38
44
42
ENGLISH
DEUTSCH
FRANCAIS
FRANCAIS
FRANCAIS
FRANCAIS
FRANCAIS
ES
pA
ño
L
po
LSKI