background image

 

Ask your shipper for a tracking number or delivery verification. Please include your email 
address so our shipper can alert you when your product is being returned to you. Periodic 
updates on the status of the repair are not available. We can only indicate the repair is in 
process until it ships back to you. Please be assured that our staff makes every effort to 
complete repairs ahead of our published wait time. Your patience is appreciated.  

Repairs can take six to eight weeks, but are usually faster. The most recent information is 
found at the LDG Customer Support Center. Send your carefully packaged unit with the 
Repair Form to: 

 

LDG Electronics, Inc. 

Attn: Repair Department 

1445 Parran Rd 

St. Leonard, MD 20685 

PRODUCT FEEDBACK 

We encourage product feedback! Tell us what you think of your LDG product. In a card, 

letter, or email (preferred) tell us how you use the product and how well it worked in your 
application. Send along a photo or even a schematic or drawing to illustrate your narrative. 
We like to share your comments with our staff, our dealers, and even other customers at 
the LDG website.  

 
 

 

Summary of Contents for Z-100A














Reviews: