background image

 

English

 

 

6.2.6. HARNESS INSTALLATION

6.3. FUEL

IMPORTANT: The fuel used is highly 
inflammable. If the fuel or the machine 
catch fire, fight the flames with a dry dust 

fire extinguisher.

Do not smoke while preparing or refueling. 
Do not approach any flame or hot element 
to the fuel.

Use unleaded fuel of 95° and synthetic oil for 2 stroke 
engines.

Motor Fuel: Mixture (Gasoline 40: Oil 1) 
2.5%. 

Mix gasoline and oil in a bottle homologated for this 
use. If you will mix more combustible just prepare 
the amount you will use the short term. Do not use 
fuel that has been stored over two months. The 
fuel stored for long periods lose its characteristics 

making it harder to start the engine and giving poorer 
performance.

FILLING THE FUEL TANK

1.  Choose an open are ato perform this situation
2.  Stay away from the area where you have made the 
  preparation of the mixture.
3.  Remove the combustible tank cap and fill with fuel.
4.  Close tighly the fuel cap and remove all traces of  
  fuel that have been spilled with a rag.

WARNINGS:
-  Always switch off the engine before refueling.
-  Do not start the machine in a closed area. The 
  exhaust fumes, the vapours of the petrol and the  
  chain oil, all contain carbon monoxide and other  
  dangerous chemical substances. In case of gas  
  concentration due to insufficient ventilation, 
  eliminate from the work area everything that 
  impedes the correct flow of air and do not work in 
  this area again until it is well ventilated and the gas  
  concentration does not happen again.
-  Do not refill fuel in areas where flames, sparks or 
  hot sources are. Refill only in ventilated areas with 
  engine off. Do not overfill the fuel to try to overfill 
  the fuel tank. In case of fuel leakage, eliminate 
  these before starting the machine, do not attempt 
  to start the engine but move the machine away 
  from the area of spillage and avoid creating any 
  source of ignition until petrol vapours have 
  dissipated.
-  Stay away at least 3 meters from the zone where 
  you have refueled before started the machine.
-  Refill fuel before to start the machine. Do not 
  unscrew the combustible tank cap while the engine  
  is running or engine is hot.

-  Do not use fuel with ethanol or methanol because 
  will damage the engine.

4

7

5

3

13

Summary of Contents for LE 25254-D

























Reviews: