background image

 

                                                                                                                                                     

User

s Manual 

For 

M542 

Economical Microstepping Driver

 

Version

 

1.0 

©

2000 All Rights Reserved

 

 

Attention: Please read this manual carefully before using the driver!

 

 

F/3, Block 2, Nanyou Tianan Industry Park, Nanshan Dist, Shenzhen, China 

PH. (86)755-26434369            FAX (86)755-26402718 

Web site: 

www.leadshine.com

    E-Mail: 

sales@leadshine.com

 

 

 

The

 

content  in  this  manual  has  been  carefully  prepared  and  is  believed  to  be  accurate,  but  no 

responsibility is assumed for inaccuracies. 
 
Leadshine  reserves  the  right  to  make  changes  without  further  notice  to  any  products  herein  to 
improve reliability, function or design. Leadshine does not assume any liability arising out of the 
application  or  use  of  any product  or  circuit  described  herein;  neither  does it convey  any license 
under its patent rights of others.   
 
Leadshine

s general policy does not recommend the use of its products in life support or aircraft 

applications  wherein  a  failure  or  malfunction  of  the  product  may directly threaten life  or  injury. 
According to Leadshine

s terms and conditions of sales, the user of Leadshine

s products in life 

support or aircraft applications assumes all risks of such use and indemnifies Leadshine against all 
damages. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

©

2000 by Leadshine Technology Company Limited. 

All Rights Reserved

www.yusto.ru 

info@yusto.ru

Summary of Contents for M542










Reviews: