manualshive.com logo in svg

Leadshine ES-DH1208, Hardware Installation Manual

The Leadshine ES-DH1208 Hardware Installation Manual is a comprehensive guide that provides step-by-step instructions for effortlessly setting up your ES-DH1208 device. This must-have manual is available for free download from 88.208.23.73:8080, offering users a convenient and easy-to-follow resource to enhance their product experience.

Share
Download
background image

iii 

Table of Contents 

Introduction to Easy Servo

.............................................................................................................................................. 1 

Getting Start

................................................................................................................................................................... 1 

Wiring Diagrams

..................................................................................................................................................... 2 

Connecting Power Supply

....................................................................................................................................... 3 

ES-DH1208

....................................................................................................................................................... 3 

ES-DH2306

....................................................................................................................................................... 3 

Connecting Motor

................................................................................................................................................... 4 

ES-DH1208 and the ES-MH2 series motor

...................................................................................................... 4 

ES-DH2306 and the ES-MH3 series motor

...................................................................................................... 4 

Connecting Encoder

................................................................................................................................................ 5 

Connecting Control Signal

...................................................................................................................................... 5 

Pulse, Direction, Enable Input

........................................................................................................................ 5 

Alarm Output

.................................................................................................................................................. 6 

Connecting PC

......................................................................................................................................................... 7 

Typical Connections

........................................................................................................................................................ 8 

Wiring Notes

................................................................................................................................................................... 9 

Configuration

.................................................................................................................................................................. 9 

Configuring ES drive by the on-board HMI

.......................................................................................................... 10 

Display Data Mode

........................................................................................................................................11 

Edit Parameter Mode

.................................................................................................................................... 12 

Configuration Example via the on-board HMI

............................................................................................. 14 

Calculating Rotation Speed and Angle

................................................................................................................. 14 

Rotating the Motor via the On-board HMI

.......................................................................................................... 15 

Rotating the Motor by Motion Controller

............................................................................................................ 15 

Rotating the ES Motor in PC Software

................................................................................................................. 16 

Power Supply Selection

................................................................................................................................................. 17 

Multiple Drives

...................................................................................................................................................... 17 

Selecting Supply Voltage

...................................................................................................................................... 17 

Recommended Supply Voltage

............................................................................................................................. 18 

Control Signal Setup Timing

......................................................................................................................................... 18 

Current Control Detail

................................................................................................................................................... 19 

Fine Tuning

.................................................................................................................................................................... 19 

Protection Functions

..................................................................................................................................................... 19 

Over-current Protection

........................................................................................................................................ 20 

Over-voltage Protection

....................................................................................................................................... 20 

Position Following Error Protection

..................................................................................................................... 20 

Frequently Asked Questions

......................................................................................................................................... 21 

Problem Symptoms and Possible Causes

............................................................................................................. 21 

Warranty

....................................................................................................................................................................... 22 

Exclusions

.............................................................................................................................................................. 22 

www.servosystem.ru    +7(495) 407-01-02

Summary of Contents for ES-DH1208




























Reviews:

No comments

Related manuals for ES-DH1208

Eaton PowerXL DM1 Series Applications Manual preview
PowerXL DM1 Series
Brand: Eaton Pages: 258
Veichi AC300 Series Technical Manual preview
AC300 Series
Brand: Veichi Pages: 95
Eaton GVX9000 User Manual preview
GVX9000
Brand: Eaton Pages: 208
Sumitomo Drive Technologies PARAMAX M Series Maintenance Manual preview
PARAMAX M Series
Brand: Sumitomo Drive Technologies Pages: 24
Leroy-Somer FMV 2107 Installation And Maintenance Manual preview
FMV 2107
Brand: Leroy-Somer Pages: 60
INVT GD350-004G-4 Operation Manual preview
GD350-004G-4
Brand: INVT Pages: 429
FujiFilm GYN101CAG-G09 User Manual preview
GYN101CAG-G09
Brand: FujiFilm Pages: 252
GE AF-600 FP BACnet Operating Instructions Manual preview
AF-600 FP BACnet
Brand: GE Pages: 47
GE D8R4 Instructions Manual preview
D8R4
Brand: GE Pages: 20
GE VAT200 Quick Start Manual preview
VAT200
Brand: GE Pages: 117
GE AF-600 FP Metasys Operating Instructions Manual preview
AF-600 FP Metasys
Brand: GE Pages: 33
GE D20A6 Instructions Manual preview
D20A6
Brand: GE Pages: 24
GE Fuji Electric MICRO-SAVER AF-300 Startup Manual preview
Fuji Electric MICRO-SAVER AF-300
Brand: GE Pages: 127
GE Druck DPI 841 User Manual preview
Druck DPI 841
Brand: GE Pages: 130
GE Fuji Electric AF-300ES Instructions Manual preview
Fuji Electric AF-300ES
Brand: GE Pages: 136
GE Ecomagination AF-600 FP Programming Manual preview
Ecomagination AF-600 FP
Brand: GE Pages: 239
GE UltraMax Installation Manual preview
UltraMax
Brand: GE Pages: 3
Emerson 03200106 Design Manual preview
03200106
Brand: Emerson Pages: 490

Brands by name

Popular brands

Load more brands