background image

Leaf LTHDMI88 / LTHDMI88E manual 

 

Page  11  Of  16 

 

 

4.3  Exclusive Source Selection 

A source can be locked to a particular zone. The exclusive source selection feature 
enables enhanced features, such as multichannel audio, 3D etc, to become active 
in  the  locked  zone  (if  supported  by  both  the  source  and  sink) 

–  even  if  the  other 

zones in the system do not support these features. 

  This feature is activated by RS232 command. 

  Any  one  zone  can  be  locked  to  a  desired  source  thus  creating  a  so-called 

“locked connection”. 

  Effectively  this  feature  overrides  the  system  merged  EDID  for  this  connection 

and allows the unique EDID for the zone to be passed through to the source. A 
typical example would be switching a 3D-capable zone to a 3D-capable source 
in instances where not all zones in the system can support 3D.  

  No other zone can connect to a source that is locked. 

  Multiple locked connections are allowed but locked sources cannot be shared. 
  When the zone of  a locked connection is disconnected the source is unlocked 

and available for selection by other sources. 

  When  the  zone  of  a  locked  connection  changes  to  a  new  source  the  existing 

source is unlocked. 

  When a global command is sent then the existing source is unlocked 

  Locking a zone to a source that is already switched to one or more other zones 

will cause that source to disconnect from those zones.  

5  Operation. 

5.1  Apply Power 

Once  power  is  applied  to  the  LTHDMI88  /  LTHDMI88E  it  will  go  through  a  Power  Up 
routine lasting  a minute or  two. The display LEDs  will cycle blue through all source 

– 

zone connection possibilities in a Right to Left direction. 

When this routine is completed the unit will reconnect the most recent Source 

– Zone 

selections  and  the  display  LEDs  will  glow  green  indicating  the  switched  sources  and 
zones.  

5.2  Calibration.   

The system should be calibrated on first use or after any new devices (source or 
zone  equipment)  are  added  or  port  allocations  changed.  Failure  to  correctly 
calibrate  a  system  may  lead  to  interruption  to  audio  and  video  at  zones  when 
other zones are switched to a source that is already in use.    

This description is valid for direct access by the front panel mounted buttons and can 
also be accessed via RS232 control. 

1.  Turn on all sources and sinks (receiver or TV). Ensure sinks are set to the 

correct HDMI input. 

2.  Press and hold operated the top button 

(A) 

on the front panel for 3 seconds 

to  commence  calibration…  or  send  appropriate  RS232  command.  The  2 
rows of LEDSs will “run” Left To Right alternatively  Blue / Green  

Summary of Contents for LTHDMI88

















Reviews: