background image

Lear UGDO 

Lear UGDO Owner’s Guide Version 3.2  Page 1 

3/27/2006 

Lear Car2U Transmitter 

The Lear Universal Garage Door Opener (LEAR Car2U ™) is a universal transmitter and can 
replace up to three different remote control transmitter units used to operate the following types 
of devices: 

x

Garage Door Opener 

x

Security Devices 

x

Home Lighting Systems 

Additional Lear Car2U ™ information can be found on the internet at 

www.learcar2U.com

 or by 

calling 1-866-57Car2U. 

Types of Garage Door Openers (Fixed Code and Rolling Code) 

Lear UGDO™ has the capability of programming rolling code and fixed code garage door 
openers:

x

Rolling code garage door openers are used for garage doors produced after 1996 and are 
code protected.  Rolling code means the coded signal is changed every time your remote 
control garage door opener is used. 

x

Fixed code garage door openers are used for garage doors produced prior to 1996.  Fixed 
code uses the same coded signal every time, which is manually programmed by setting 
DIP switches for a unique personal code.

If you do not know if your garage door opener is a rolling code or fixed code device, open your 
garage door opener’s remote control battery cover.  If a panel of DIP switches is present as 
shown in the typical remote device shown below, your garage door opener is a fixed code device.
If not, your garage door opener is a rolling code device. 

Short Term Confidentiality Requested

Summary of Contents for UGDO









Reviews: