background image

HH/E01

LECTROSONICS, INC.

6

Capsule and Battery 

Installation

A common threaded mount allows the use of a va-

riety of different capsules from different manufactur-

ers. Capsules are attached with a right-hand thread.

The control panel and battery compartment are 

accessed by opening the lower housing. Rotate the 

housing as shown and pull it downward until you feel 

the detent.

A mic capsule is 

threaded onto the body 

of the transmitter in the 

direction shown.

Do not overtighten it.

The lower housing opens by rotating 

it in the direction shown. After the 

threads are disengaged, pull the 

housing downward until it engages 

the detent that holds it open.

The threaded interface is a 1.25 inch 

opening with 28 threads per inch and 

three contact rings

To insert batteries, close 

the eject lever and insert 

the upper contacts 

first (closest to the mic 

capsule). Polarity is 

marked on the label in 

the bottom of the battery 

compartment.

Do not touch the contacts between the mic capsule 

and transmitter body. When necessary, the contacts 

can be cleaned with a cotton swab and alcohol.

To remove the batteries, pull the eject lever outward. The 

battery tips will move outward, making them easier to grasp.

Summary of Contents for HH/E01

















Reviews: