background image

    

LECTROSONICS, INC.

10

5) Adjust Transmitter Input Gain

NOTE: This adjustment is very important, since it will determine the 

signal to noise ratio and dynamic range that the system will deliver.

Lectrosonics L-Series Transmitters:

The two bicolor Modulation LEDs on the transmitter control panel provide a 

visual indication of the audio signal level entering the transmitter. The LEDs 

will glow either red or green to indicate modulation levels as shown in the 

following table. Full modulation is achieved at 0 dB, when the “-20” LED first 

turns red. The limiter can cleanly handle peaks up to 30 dB above this point.

Signal Level 

-20 LED 

-10 LED

Less than -20 dB 

 Off 

 Off

-20 dB to -10 dB  

 Green 

 Off

-10 dB to +0 dB 

 Green  

 Green

+0 dB to +10 dB 

 Red 

 Green

Greater than +10 dB 

 Red 

 Red

NOTE: It is best to go through the following procedure with the 

transmitter in the standby mode so that no audio will enter the sound 

system or recorder during adjustment.

1)  With fresh batteries in the transmitter and power the unit on in the standby 

mode (a brief press on the power switch with L-Series transmitters).

2)  Navigate to the Gain setup screen.   
 

Gain

Freq.
ProgSw
Compat

-40

-20

0

Gain

25

LMb menu shown

3)  Prepare the signal source. Position a microphone the way it will be used 

in actual operation and have the user speak or sing at the loudest level 

that will occur during use, or set the output level of the instrument or 

audio device to the maximum level that will be used.

4)  Use the   and   arrow buttons to adjust the gain until the –10 dB glows 

green and the 

–20 dB LED starts to flicker red during the loudest peaks 

in the audio.

5)  Once the transmitter input gain has been set, the signal can be sent to 

the sound system or recorder for level adjustments, monitor settings, etc. 

6)  Always leave the transmitter gain adjustment set according to these 

instructions, and do not change it to adjust the audio output level of the 

receiver.

Other Transmitters:

Earlier Lectrosonics transmitters provided LEDs to accurately indicate full 

modulation, with continuously variable gain controls for a precise adjustment. 

The LEDs operate in the same manner as those shown here for the L-Series 

transmitters.

Summary of Contents for L series













Reviews: