background image

29 June 2016

581 Laser Road NE   •  Rio Rancho, NM  87124  USA  •  www.lectrosonics.com
(505) 892-4501  •  (800) 821-1121  •  fax (505) 892-6243  •  sales@lectrosonics.com

LIMITED THREE YEAR WARRANTY

The equipment is warranted for three years from date of purchase against defects in

  

materials or workmanship provided it was purchased from an authorized dealer. This  
warranty does not cover equipment which has been abused or damaged by careless 
handling or shipping. This warranty does not apply to used or demonstrator equipment.

Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any  
defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot 
correct the defect in your equipment, it will be replaced at no charge with a similar new 

item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you.

This warranty applies only to items returned to Lectrosonics, Inc. or an authorized  

dealer, shipping costs prepaid, within three years from the date of purchase.

This Limited Warranty is governed by the laws of the State of New Mexico. It states the 
entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any 
breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR 

ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT  
SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL,  

OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE 
THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE 
POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF  
LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE 

EQUIPMENT. 

This warranty gives you specific legal rights. You may have additional legal rights which 

vary from state to state. 

Summary of Contents for SPN1612

























Reviews: