Led Lenser 6005, Operating Instructions Manual

4

LED LENSER® * SEO 5

push a second time within 2 seconds, the SEO5 

glows with lower brightness (Light Function 

Dim). When you push the second time within 

2 seconds but keep the button pressed down, 

you can  change the brightness infinitely. For 

the time that the switch button is pressed, the 

brightness varies between full and reduced 

brightness. The SEO 5 extinguishes (blinks) 

for a short moment as soon as the highest or 

lowest brightness is reached. At both ends of 

the SEO 5 goes off shortly, and then again to 

be lighter or darker(a blinking signal happened 

at both ends). When you release the switch 

button you lock the current brightness. This 

brightness is retained for the Light Function 

Dim even if you turn the head lamp off.

After the Light Function Dim (altogether 3 

times fast switching, i.e. you do not wait longer 

than 2 seconds between each switching) comes 

the Light Function Signal (slow even flashing) 

in the Light Program White. 

Additional switching turns SEO 5 off and the 

circle starts again with the Light Function 

Power when you press the switch button again.

So the Light Functions are in a loop. But please 

note that you turn off the head lamp by every 

switching if since the previous switching more 

than 2 seconds have elapsed. For example in 

case you let pass more than 2 seconds after  

you turned the Light Function Dim on the next 

switching will not change to head lamp to Light 

Function Signal but will turn the SEO 5 off.

5.2 Light Program „Red Night Vision“

If the Lighting Program „Red Night Vision“ is 

enabled (see Point 5), you can use the red light of 

the head lamp.

When the switch button is pressed, when the SEO 

5 is off, the head lamp glows in the Light Function 

Power at full brightness in red. When you switch 

a second time within 2 seconds, the SEO 5 blinks 

in the Light Function Signal (slow even flashing).

The Light Function Signal is the last Light 

Function that can be used in the Light Program 

“Red Night Vision” so additional switching turns 

SEO 5 off and the circle starts again with the 

Light Function Power when you press the switch 

button again. 

So the Light Functions are in a loop. But please 

note that you turn off the head lamp by every 

switching if since the previous switching more 

than 2 seconds have elapsed. For example in 

case you let pass more than 2 seconds after 

you turned the Light Function Power on the next 

switching will not change to head lamp to Light 

Function Signal but will turn the SEO 5 off.

6 „Transport Lock“

Under Point 5 it has been described how to 

switch between the white and the red LED. This 

takes place when the SEO 5 is off and the switch 

button is pressed only for approx. 2 seconds. The 

head lamp will change from red to white or from 

white to red. But when the switch is pressed 

longer (approx. 5 seconds) until the light turns off 

you have enabled the „Transport Lock“. Then the 

SEO 5 can not be turned on again but the red LED 

flashes for a short moment to indicate that this 

function is activated in case the switch button is 

pressed. The SEO 5 therefore cannot be switched 

on, either intentionally or unintentionally and 

inadvertently consume energy.

Only when you hold the switch button pressed for 

5 seconds again this function („Transport Lock“) 

is deactivated again and the lamp is in the Light 

Program White.

7. Reset function

If the used alkaline batteries, NiMH-

Accumulators or an Accumulator-Pack of a 

SEO 7R are taken out the battery box you have 

"reset" the SEO 5.

You have thus reset a few functions:

- The „Transport Lock“ (see Point 6) is 

deactivated

- The Light Function Dim (see Point 5.1) is set 

to low brightness

- The Light Program White (see Point 5) is 

activated

8. Use of rechargeable batteries

The SEO 5 indicates by the flashing of the red 

LED that it is running out of energy in near 

future. Please change the batteries respectively 

the accumulators in time.

In the scope of delivery of the SEO 5 are alkaline 

batteries. These can not be charged!

The following information applies only in case 

you use in your SEO 5 NiMH-Accumulators 

respectively the Accumulator-pack of a SEO 

7R. These are not scope of delivery of SEO 5! 

In case NiMH-Accumulators (see Point 1) are 

used, these must be charged in approved 

external chargers.

Always charge in a dry place!

Do you use the Accumulator-Pack of a SEO 7R 

please note that this can only be charged with 

the charger and the charger cable of the SEO 

7R or by a USB port (see below)! 

In case the plug and the charger are not 

connected already please connect them so that 

the connection clicks.

The charger of SEO 7R has a USB port, which 

must be connected with the corresponding 

port at the charging cable in order to charge 

the SEO 7R Accumulator-pack. The other 

side of the charging cable (micro USB) must 

be connected to the Accumulator-pack. You 

will therefore have to open the battery box 

possibly. The Accumulator-pack of SEO 7R 

has two charging ways, either it loaded in the 

battery box of SEO 5 or can be removed out of 

the battery box for charging. The charger of the 

SEO 7R can only be used for charging of this 

Accumulator-pack.

The last step is to connect the plug into a 

socket (Input: 100 V to 240 V / 50 Hz to 60 Hz). 

When charging is completed (after maximum 2 

to 3 hours), unplug the charger from the socket 

again and the charging cable (micro-USB) of 

the Accumulator-pack. But it is no problem to 

go on loading the Accumulator-pack although it 

is already full.

Instead of connecting the charging cable of the 

SEO 7R to the USB port of the charger, you can 

also connect it to a different USB port (5 V / 

900 mA) e.g. of a computer.

While using our optionally available car USB 

charger connection (Led Lenser Car Charger: 

Item no. 0380), the Accumulator-pack also can