Led Lenser H14R.2, Operation Manual

We are delighted that you have purchased one 

of our products.

These are usage instructions to help you 

familiarise yourself with your new purchase. 

All the documents accompanying the product 

must be read attentively before using the 

product, preserved carefully and if the product 

is transferred to a third party, the documents 

must be handed over as well. This ensures that 

maximum benefit is drawn from the product 

and questions from users are anticipated before 

they arise.

Above all, comply with the warnings and safety 

instructions and dispose of the packaging 

material properly.

Additional information for H14R.2 with “TEST-

IT” function

Your LED LENSER H14R.2 headlamp is 

packaged with a “TEST-IT” function (item no. 

7399-R). This allows users to test the brightness 

while the product is still in the package. For 

testing, simply push the yellow “TEST-IT” button 

on the front of the package. When testing, please 

do not look directly into the light.

The “TEST-IT” button is connected to the battery 

housing of the H14R.2 via two wires and should 

be removed prior to use.  

To remove the “TEST-IT” button and wires, open 

the battery box rear cover and remove 4xAAA 

alkaline battery (see also “Changing of the 

battery “further below). Separate the two “TEST-

IT” button wires from the battery housing by 

pulling on each wire until it releases from the 

battery housing.  Insert the battery and noting 

the correct polarity. Close the battery box rear 

cover. Please dispose and recycle the packaging 

and “TEST-IT” button with the wires according to 

the local regulations.

Product

7299-R, 

LED LENSER® 

H14R.2

7399-R, 

LED LENSER® 

H14R.2 (Blister)

Version of the operating manual: 

1.3

1. Battery set:

1 x Li-ion battery pack 3.7 V 4400mAh 

4XAA alkaline battery (Blister)

2. Switching on and off

The H14R.2 has two switches. The front switch 

is located on the right side of the headlamp 

housing. This switch button is used to turn the 

H14R.2 ON/OFF. It is also used to activate the 

various Light Programs and Lighting Functions 

(see section 5.1) and the “Transport Lock” 

function (see Point 7). The “Multi-function 

Wheel” switch is located on the backside at the 

upper part of the  battery box. This allows you 

to adjust the brightness and flash rate infinitely 

and to change into different modes. In this 

switch is also a battery indicator and the red 

rear light located (see Section 5).

3. Focus

In the front, narrower region of the headlamp 

housing is the reflector lens through which the 

light of the white LED is focusable. The light 

is focusable through our patented "Advanced 

Focus System", by pushing easily the lamp head 

forward and backwards (Speed Focus). 

You also can adjust the hinge of the headlamp. 

Depending on whether you want to illuminate 

an area in the distance or in front of you. For 

this you can simply tilt the part of the lamp 

head, which contains the reflector lens and 

the white LED. The gradual detent allows also 

intermediate positions.

4. Smart Light Technology (SLT) 

The H14R.2 is equipped with our Smart Light 

Technology (SLT). Thanks to the use of a 

microcontroller, the light output of the white 

front LED can be controlled and the user can 

use various Energy Modes, Light Programs and 

Light Functions. The red rear light also has two 

light functions.  Through the front switch and the 

“Multi-function Wheel" switch on the back, the 

handling is simple and user-friendly. To turn the 

headlamp on and off and to select the various 

Light Functions etc., the front switch has to be 

used. (see point 5). 

What basically applies is that the brightness 

of the H14R.2 is monitored by the in-built 

temperature control unit.

5. Light Programs and Light Functions

In the H14R.2 are equipped with one white LED 

(LED = Light Emitting Diode) , 

The white LED is very strong, ideal for normal 

use, for example if the Speed Focus or the 

adjustment of the angle of light beam to the 

horizontal should be used. This very bright 

white light might be not good when your eyes 

have become accustomed through the so-called 

dark adaptation to low ambient light. 

5.1 Light Program White (Front light)

In H14.2, there are three different modes (Easy 

Low, Easy Power, Signal). The default mode is 

Easy Low.

When the product is off, press the “Multi-function 

Wheel” switch the for 5 second, it will achieve 

mode transition, blink for one time, that means 

you has entered sub-mode one; blink for two 

times, that means you has entered sub-mode 

two; and 3 times blink for three times, that 

means you has entered sub-mode three.

a) Light Mode one - Easy Low: 

when the product 

is off, push the front switch hardly until you hear 

click sound, the white LED will glows with lower 

brightness (light function: Low Power); second 

touch the white LED will glows full brightness 

(light function: Power), third time touch the 

button is off; 

b) Light Mode two - Easy Power: 

when the 

product is off, push the front switch hardly until 

you hear click sound, the white LED will glows 

with full brightness (light function: Power); 

second touch the white LED will glows with 

lower brightness (light function: Low Power), 

third time touch the button is off; 

c) Light Mode three - Signal:

 when the product 

is off, push the front switch hardly until you hear 

click sound, the white LED will glows with full 

brightness (light function: Power); second touch 

the white LED flashes frequently (12 Hz) (light 

function: Signal), third time touch the button is 

off; 

02

English 

|

 Page 02-05

GB