Led Lenser H7R.2, Operating Instructions Manual

02

English 

|

 Page 02-05

GB

We are delighted that you have purchased one 

of our products.

These are usage instructions to help you 

familiarize yourself with your new purchase. 

All the documents accompanying the product 

must be read attentively before using the 

product, preserved carefully and if the product 

is transferred to a third party, the documents 

must be handed over as well. This ensures that 

maximum benefit is drawn from the product 

and questions from users are anticipated 

before they arise.

Above all, comply with the warnings and safety 

instructions and dispose of the packaging 

material properly.

Additional Information for H7R.2 with “TEST 

IT” Function

Your LED LENSER H7R.2 headlamp is packaged 

with a “TEST IT” function (item no. 7398). This 

allows users to test the brightness while the 

product is still in the package. For testing, 

simply push the yellow “TEST IT” button on the 

front of the package.  When testing, please do 

not look directly into the light.

The “TEST IT” button is connected to the 

battery housing of the H7R.2 via two wires and 

should be removed prior to use.  

To remove the “TEST-IT” button and wires, 

open the battery box rear cover and remove 

4xAAA alkaline battery (see also “Changing of 

the battery“ further below). Separate the two 

“TEST IT” button wires from the battery housing 

by pulling on each wire until it releases from 

the battery housing. Insert the batteries in and 

noting the correct polarity. Close the battery 

box. Please dispose and recycle the packaging 

and “TEST IT” button with the wires according 

to the local regulations.

Product

7298, 

LED LENSER® 

H7R.2

7398, 

LED LENSER® 

H7R.2 (Blister)

Version of the operating manual: 

1.4

1. Battery set:

1 x Li-ion battery pack 3.7 V (1400 mAh)

4XAAA alkaline battery (Blister)

2. ON and OFF

The H7R.2 has two switches. The front switch 

is located on the right side of the headlamp 

housing. This switch button is used to turn the 

H7R.2 ON/OFF. It is also used to activate the 

various Light Programs and Lighting Functions 

(see section 5.1) and the “Transport Lock” 

function (see Point 7). 

The “Multi-function Wheel” switch is located on 

the backside at the upper part of the battery 

box. This allows you to adjust the brightness 

and flash rate infinitely and to change into 

different modes. In this switch is also a battery 

indicator and the red rear light located (see 

Section 5.2).

3. Focus

In the front, narrower region of the headlamp 

housing is the reflector lens located. This lens 

focused the light of the white LED through our 

patented "Advanced Focus System". 

The reflector lens is held by a plastic ring. You 

can rotate that plastic ring using two fingers, 

and thus adjust the focus quickly and easily. 

This is our Turning Focus, which allows the 

adjustment of the light beam’s focus.

You also can adjust the hinge of the headlamp, 

depending on whether you want to illuminate 

an area in the distance or in front of you. For 

this, you simply tilt the part of the lamp head, 

which containing the reflector lens and the 

white LED. The gradual detent allows also 

intermediate positions.

4. Smart Light Technology (SLT) 

Smart Light Technology (SLT) is a program 

that consists of computer optimized 

microcontrollers which allows our products 

to have various lighting functions. The H7R.2 

is equipped with this technology and is 

therefore able to use various Light Programs 

and Functions. The front switch at the top of 

the lamp head can turn the lamp On and Off, 

change the brightness, and turn on functions 

like the boost mode and others. Pressing the 

“Multi-function Wheel" switch on the upper 

part of the battery box can turn on the red light. 

This “Multi-function Wheel" switch can also be 

rotated to further adjust the brightness of your 

headlamp light . 

5. Light Programs and Light Functions

The H7R.2 is equipped with three LEDs (LED 

= Light Emitting Diode), one white LED in the 

front housing, and two other red LED’s in the 

battery box.

The white LED is very strong and ideal for 

normal use. This very bright white light may 

not suitable when your eyes have become 

accustomed through the dark or low ambient 

light. 

The red LED is not meant to illuminate a space, 

but as a way to be seen or identified (see 

Section 5.2).

5.1 Light Program White (Front light)

In H7R.2, there are three different modes (Easy 

Low, Easy Power, Signal). The default mode is 

Easy Low.

When the product is off, press the “Multi-

function Wheel” switch for 5 second. It will 

achieve mode transition. Then white LED will 

blink once (3Hz) to indicate that it is mode one; 

then blink twice for mode two; and finally blink 

thrice for mode three.

a) Light Mode one - Easy Low:

 when the 

product is off, firmly press the front switch 

button until it blinks once. The white LED will 

glow at its lowest brightness (light function: 

Low Power dim light). A second touch to the 

button on top of the lamp will turn ion the lamp 

to its full brightness (light function: Power 

strong light), and third touch will turn the lamp 

off. 

b) Light Mode two - Easy Power:

 when the 

product is off, firmly press the front switch 

until it blinks twice. The white LED will glow at 

its fullest brightness (light function: Power). A 

second touch to the button on top of the lamp 

will turn on the lamp to its lowest brightness 

(light function: Low Power), and third touch will 

turn the lamp off.