Led Lenser H7R.2, Operating Instructions Manual

03

LED LENSER® * H7R

.2

c) Light Mode three - Signal: 

when the product 

is off, firmly press the front switch until it 

blinks thrice. The white LED will glows with full 

brightness (light function: Power). A second 

touch to the button on top of the lamp will start 

the strobe (12 Hz) (light function: Pulse), and a 

third touch will turn the lamp off.

Note: In the low power- and power- function, 

you can adjust the brightness stepless by 

turning the multi-function "Wheel" switch (Dim 

function). A short flash indicates the darkest (5 

lumens) or brightest setting.

In the Pulse- function, you can speed up or 

slow down the flashing frequency by turning 

the multi-function "Wheel" switch (Pulse 

function).

d) Boost Mode: 

in each setting, press the front 

switch for 2 seconds, you will enter to boost 

mode, after a short time the flashlight will 

return to previous choosing.

The Light Functions above are in a loop. 

Note: when switching between modes, press 

the “Multi-function Wheel” switch button no 

longer than 2 seconds, otherwise the product 

will turn off. 

5.2 Light Program Red (rear light)

ON-OFF / transition mode (change modes 

within 2 seconds, but more than 2 seconds the 

lamp will turn off) / charge indicator/ battery 

capacity indicator function is available for the 

red LED:

1) ON-OFF function: 

in any status, two red LED 

will light up by pressing the “Multi-function 

Wheel” switch once: the LEDs will start to blink, 

by pressing the switch twice; at the third push 

the LEDs will turn OFF.

2) Charge indicator function: 

the red LED will 

glow when charging. After full charge, the LED 

will glow green. Note that the white LED will 

not work when charging.

3) Battery capacity indicator: 

when you start 

to use white LED, the red LED on the battery 

box will glow for 5 seconds and then turn off. 

Green means that the battery capacity is at 

50%-100%; yellow means the battery capacity 

is at 20-49%; when the red LED is glowing the 

battery capacity is lower than 19% & not suit 

for long time use, therefore must be charged. 

6. Energy Modes

By selecting one of the two Energy Modes 

(Energy Saving or Constant Current), you 

decide how the energy contained in the 

accumulator or batteries are used.

6.1 Energy Saving:

 The light output is 

controlled by the integrated Smart Light 

Technology (SLT). The brightness is adjusted 

to the realistic conditions that occur during 

normal use of the lamp, thus providing a longer 

burn time.

6.2 Constant Current: 

This Energy Mode allows 

the continuous use of all the Light Functions 

with a constant light output. This Energy Mode 

is preferrable when a high brightness level is 

more important than a long burn time 

6.3 Changing the Energy Modes

Changing the Energy Modes can only be done 

when the flashlight is in Light Program White 

and the lamp is turned Off. To change the 

energy mode, with the white LED off, press the 

“Multi-function Wheel” on the back 8 times, 

then on the 8th click keep the knob pressed 

for approx. 2-4 seconds. This should allow 

you change between the “energy mode“ and 

“constant current mode.“ You know which 

mode you are in when:

a) Constant current mode: 

the brightness 

reduces immediately in 2 seconds. 

b) Energy saving mode:

 the brightness reduce 

gradually to zero.

With this procedure, you can switch between 

the two Energy Modes. It is not possible to 

determine in which Energy Mode the H7R.2 

is. To find this out, you must carry out the 

procedure. If the H7R.2 is thereafter not in 

the desired Energy Mode any more, you must 

repeat the procedure again. The flashlight will 

reset to energy saving mode if you change the 

battery or cut the power. 

7. “Transport Lock”

When the H7R.2 switched Off, press the front 

switch for approx. 5 seconds till the light turns 

off in order to enable the “Transport Lock.” The 

H7R.2 cannot be turned on any more, either 

intentionally or unintentionally. Accidental 

power consumption is not possible.

To deactivate the “Transport Lock”, just press 

the front switch again for 5 seconds. The 

headlamp will now return to the Light Program. 

8. Reset function

If the Accumulator-Pack & the alkaline 

batteries are taken out the battery box you 

have "reset" the H7R.2. You have thus reset a 

few functions:

The Light Program White (see Section 5.1) is 

activated

The Light Function Dim (see Section 5.1) is set 

to low brightness

As Energy Mode Energy Saving is activated (see 

Section 6).

The “Transport Lock“ (see Section 7) is 

deactivated

9. Charging

The H7R.2 indicates by the flashing white LED 

that it is running out of energy in near future. 

Please charge the Accumulator-pack in time. 

Charge the Accumulator-pack of your H7R.2 in 

a dry place and only by using the charger that 

is included in the delivery or by a USB port (see 

below). 

The following information applies only to the 

included accessories. You cannot charge any 

other accumulators or batteries in the H7R.2. 

In the scope of delivery of the H7R.2 there 

is a plug and a charger. In case both are not 

connected already, please connect them so 

that the connection clicks.

H7R.2 charger has a USB port which must be