background image

1-6 WARRANTY 

 

This laminator is guaranteed against defects in material and workmanship for a period of two years 
after date of shipment.  Defective parts will be replaced without cost within the warranty period, 
provided the laminator has not been abused, altered or operated contrary to instructions.  Ledco, Inc. 
shall not be liable for any alternations or repairs except those made with its written consent. 

 

This obligation under warranty shall not extend to the following: 

 

 

The adjustment or replacement of parts which are the normal responsibility of the owner.  For 
example, rubber rollers, scratched or chipped paint, loose fasteners (screws, nuts, etc.), or other 
items that show wear under normal use; i.e. “normal wear parts.” 

 

 

Normal operating adjustments to heat, speed, tension, etc. 

 

 

Parts that are not manufactured by Ledco, Inc.  If the individual manufacturer warrants these items, 
their warranty is, in turn, passed on to the original purchaser of the laminator.  Ledco, Inc. does not 
incur any obligation or liability as a result of the warranties that are the sole responsibility of the 
appropriate individual manufacturer. 

 

Any laminator that proves defective during the warranty period may be returned to Ledco, Inc. unless 
it is decided that the necessary repairs can be made during a service call.  Notice of the defect should 
be submitted in writing or by phone to Ledco before any steps are taken to repair or return the 
machine.  Phone:  585-367-2392   Fax:  585-367-2978 

 

If the machine is returned, the following should accompany it. 

 

Customer name, address and phone number 

 

Written particulars regarding the malfunction 

 

Date of installation 

 

Serial number of the machine. 

 

All returns must have a return authorization number on the outside of the shipping 
container. 

Send all returned equipment freight PREPAID to: 

 

 

 

Ledco, Inc., 4265 North Main Street, Hemlock, NY 14466 

 

If your machine needs servicing after the warranty has expired, please contact your dealer.   Ledco, 
Inc. does offer technical support if your dealer is unable to assist. 

 

This warranty is expressly in lieu of all other warranties expressed or implied, including the warranties 
of Merchantability and Fitness For Use and of all other obligation or liabilities of Ledco, Inc., and said 
company neither assumes nor authorizes any other person to assume it for any other obligation or 
liability in connection with the sale of this laminator except as provided for above. 

 

Further, this warranty will not apply to any machine or part thereof which has been damaged as 
a result of an accident or as a result of the abuse, misuse, or neglect of the machine.  The 
warranty is also void if the laminator has been altered or repaired by any other than an 
authorized repair facility or dealer.  

 

If you have any questions about this warranty, contact:  
Ledco:  tel: 585-367-2392  

  fax: 585-367-2978 

 

10

Summary of Contents for Professor 27




































Reviews: