5) Pull swivel assembly firmly from hose spool (SEE FIG. 13 and 14).
6) Unscrew Hose Clamp and pull hose off hose barb on swivel
(SEE FIG. 15).
7) Pull remaining length of hose out reel opening located at the reel front.
8) Take replacement hose through opening located at the front of reel.
Thread hose through hose leveling mechanism (SEE FIG. 16).
9) Insert hose through the center of the hose spool. Four openings are
referenced with the following hose I.D. dimensions located at the center
of hose spool: 3/8 in., 1/2 in., 5/8 in. & 3/4 in.. Locate the hose I.D. and pull
through that opening
10) Replace hose onto hose barb, tighten hose clamp onto hose & place
swivel into hose spool housing.
11) Replace wear ring and fasten with wear ring screws. Replace wear plate
so that the swivel drive tabs insert into wear plate tab receivers
(SEE FIG. 18).
12) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
13) Turn swivel so that fastener holes of swivel and sideplate align. Replace
the four sideplate fasteners and tighten.
14) Remove screw driver.
15) Retract hose back into reel.
Replacement
Swivel Body
Part #
Replacement
Hose Stopper
Part #
L8305 / L8305FZ / L8306 / L8306-EU
L8306FZ / L8310 / L8310-EU
RP005007-38
RP005026
RP005007-12
RP005027
L8344 / L8346 / L8349
RP005007-58
RP005028
Swivel Kits
1) Repeat steps 1-6 in the HOSE REPLACEMENT procedure.
2) Place hose onto hose barb of new swivel body. Tighten hose clamp onto
hose & place swivel into hose spool housing.
3) Replace wear ring and fasten with wear ring screws. Replace wear plate
so that the swivel drive tabs insert into wear plate tab receivers (SEE
FIG. 18).
4) Replace sideplate so that the plate snaps flush to side of reel. Turn
sideplate until locking tabs connect to sideplate.
5) Turn swivel so that fastener holes of swivel and sideplate align.
Replace the four sideplate fasteners and tighten.
6) Remove screw driver.
7) Retract hose back into reel.
Troubleshooting Questions
Suggested Tips
1. Hose will not retract back into the unit.
1a. Ensure the Latch Spring & Pawl isn't engaged
1b. Follow the Tension Adjustment Procedure (See pg 2)
1c. Replace Internal Drum Assembly
2. Hose will not fully retract back into the unit.
2a. Follow the Tension Adjustment Procedure (See pg 2)
2b. Is the replacement hose too heavy? (Rubber?)
2c. If hose bunches, adjust the Layering Mechanism Timing
3. Hose will not lock in 3' intervals.
3a. Are you releasing the hose too quickly?
3b. Is the Latch Spring & Pawl engaged?
3c. Replace the Latch Spring & Pawl Mechanism
4. Internal leak.
4a. Replace the hose if it is damaged.
4b. Replace the Swivel Body (a-rings are not available separately)
Levelwind
TM
Troubleshooting Guide
TECHNICAL ASSISTANCE:
(SEE FIG. 17). Pull enough hose to allow the hose
to connect to hose barb on swivel.
Call 800-645-8258 or email service@legacymfg.com
if you have any questions regarding the installation
or operation of this reel.
Levelwind™ Model #
L8335 / L8335-EU / L8335FZ / L8345
L8350 / L8340FZ
