background image

Unit 404     Glenfield Park Business Centre     Blakewater Road     Blackburn     Lancashire     BB1 5QH

Tel: 01254 695244     Fax: 01254 695255     Web: www.legend-fires.com     Email: info@legend-fires.com

Draft G - 19/09/16

Non Display handset with pilot burner

If the fire does not start at the first attempt it may retry several times to do so. At the end of trying if it cannot

ignite the burner; it will show a RED light on the handset and on the fire control and stop the fire.

• If the fire does not light first time, allow fire to cool and then repeat lighting fire up to 10 times, as it may only be

a temporary reason that will clear after a few attempts..

• Reset the fire control by pressing the handset as if you were doing a normal start. This will clear the red light

and allow another subsequent restart attempt.

• If the fire does not light, replace all the batteries in the handset and the  fire control, (5 x AA Alkaline in total,

with batteries that do not leak) with new and known to be good batteries and repeat the above starting of the fire.

• While replacing the batteries, check that the battery contacts are not contaminated with anything that may have

leaked out of the batteries that may have damaged the contacts.

• If the fire still fails to light check to see if the pilot flame on the pilot burner, is lighting during the starting

sequence. If not then clean the pilot as described in Cleaning the pilot section of the booklet.

• Check to see if there is a spark appearing on the pilot spark plug and check to see if there is any contamination

around it that might be preventing the ignition spark from happening.

Display handset with pilot burner

As above except instead of the red LED light on the handset there will be a letter E and a to digit number where

the time is usually displayed. Do the same actions as above to try and resolve the reason for non ignition of the

burner.

If you cannot resolve the problem, then call: 

01254 695244.

Your appliance is guaranteed for one year from proof of purchase. Should the appliance prove defective within

that period we agree to repair or replace (at our discretion) the component or appliance provided that:

1. The user can produce a receipt for proof of purchase/installation.

2. The appliance has been supplied by an authorised stockist and has been installed by a qualified installer, all

installation and operating instructions have been strictly adhered to.

3. No alterations have been carried out on the appliance or component parts without our written consent.

4. The appliance has not been used for any purpose other than those intended.

5. The appliance has not been damaged accidentally or due to fair wear and tear.

Guarantee claims should be made through your appliance supplier. The Guarantee is restricted to UK Mainland

and is additional to your statutory rights.

TROUBLE SHOOTING (USER)

GUARANTEE

Summary of Contents for Ethos 3S

























Reviews: