background image

Please also familiarise yourself with the 

Notes for the Installer and End User 

on page 3.

Never place combustible material directly in front of this appliance. Floor covering such as carpet is acceptable
but must be a minimum of 300mm from the incandescent flame. Any combustible shelf must be at least 215mm
above the fire trim, providing the shelf depth is 150mm or less.

OPERATION AND CONTROLS

It is most important that the operator of this gas appliance has fully read and understood all the operating,
cleaning and maintenance procedures as laid out in these instructions.

USER INSTRUCTIONS

9

Lighting Procedure

1. Push down the lever until the spark ignition begins to ‘click’ (position 2) and continue to hold down for 10 to 15
seconds until the pilot establishes.

2. With the pilot established, give the mechanism the extra 2-3mm downward push to allow gas to the main
burner.

3. Slowly lift the lever to position 4 to give the minimum setting.

4. Slowly lift the lever again to position 3 to give the maximum setting.

5. When turning down to the minimum setting from maximum, 

it is essential that the lever is fully pushed

down to the ignition setting and then lifted back up to the minimum setting.

6. To switch off the appliance completely, simply lift the lever fully to the top position.

NOTE: 

The pilot assembly fitted to this appliance has an oxygen depletion sensor built in to monitor the room

for products of combustion. If the sensor should operate and switches the appliance off, re-ignite the
appliance following the procedure above. Should the appliance repeatedly activate the sensor, a specialist
should be called to inspect the appliance.

7. The fire must always be run on the high setting for at least the first 30 minutes to allow the chimney/flue to
warm up. This allows the ‘pull’ of the flue to commence. After this period, a lower setting can be obtained by
sliding the knob down to POSITION 4.

The fire is a very efficient heating appliance and therefore care must be taken not to touch working surfaces
including the glass when operating. This particularly applies around the perifery of the glass and louvre outlet.
Other areas considered to be working surfaces are everything except the control handles and fret knob.

WARNINGS:

Never throw any type of rubbish on or otherwise disturb the fuel bed.

Any alteration to this appliance including its ceramic components may render it inoperable and
unsafe.

ALWAYS run this appliance on the high setting for the first 30 minutes (minimum) - Failure to do this
may result in poor combustion and excessive sooting.

Never use this appliance if the glass panel is broken, removed or is open.

Fig. 8

POSITION 1

OFF

POSITION 2

IGNITION/PILOT

POSITION 3

MAXIMUM SETTING

POSITION 4

MINIMUM SETTING

Summary of Contents for Evora

















Reviews: