background image

Catalogue number(s): 0 882 30

Technical data sheet: F01163EN/01  

Updated: 30/03/2015  

             Created: 07/07/2010

1/8

Configuration tool with screen

128, av. du Maréchal-de-Lattre-de-Tassigny - 87045 LIMOGES Cedex

Tel: +33 (0)5 55 06 87 87 Fax: +33 (0)5 55 06 88 88

www.legrand.com

Using this infrared configuration tool the user can, without touching the 

device:

-  set the parameters of SCS and KNX self-contained sensors, dynamic 

light strips and SARLAM bulkhead lights (time delay, daylight setpoint, 

detection sensitivity, etc.)

-   adjust, correct, debug the system according to the characteristics of the 

installation location and customer requirements

-  save the settings (maximum of up to 26 configuration files)

- duplicate onto other sensors (copy/paste a typical setting)

Infrared communication technology (4 m max.) 

In the direction of the product to be measured

At a maximum angle of +/-15° in the axis of the IR transmission and 

reception LED (see figure)

4 m

4 m

+/- 15°

+/- 15°

Backlit screen (automatic switch-off)

Weight: 71 g

Impact resistance: IK04

Operating temperature: -5°C to +45°C

Storage temperature: -20°C to +70°C

Recharging:  Use a mini USB cable (not supplied) to recharge the 

configuration tool via a standard USB socket.

Note:  Updating software is available on our website

Works with all factory pre-set compatible sensors (infrared, ultrasound 

or dual technology) with dynamic light strips and SARLAM bulkhead 

lights.

After fully interrogating the device, only the parameters concerning this 

device appear.

CONTENTS Page

1. 

Use

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2. 

Technical characteristics

. . . . . . . . . . . . . . .1

3. 

Navigation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

4. 

Updating

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

5. 

 

Standard EN12464-1  

recommendations

  . . . . . . . . . . . . . . . . . . . . .7

6. 

Care

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

7. 

Standards

  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2. TECHNICAL CHARACTERISTICS

2. TECHNICAL CHARACTERISTICS (CONTINUED)

1.USE

Display screen

Control and navigation 

keys

On/Off and OK

IR transmission 

and reception LED

Function access 

keys
Mini-USB 

connector

Summary of Contents for 0 882 30









Reviews: