26 / 26
DX³ 4
-pole RCBO
6000 A/10 kA
Cat. N°(s) :
4 111 85, 86, 87, 88, 89 / 4 112 04, 05, 06, 07,
4 112 08, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35,
4 112 36, 37, 38, 39, 40, 41, 42, 44, 45, 46, 47, 49, 50, 51,
4 112 52 / 4 113 50, 56, 57, 59, 60, 61, 62, 80, 81
8. AUXILIARIES AND ACCESSORIES
Wiring accessories:
.
Supply busbar:
-HX
3
4-pole universal supply busbar (Cat. No. 4 049 44, 9 45)
. Connection Terminals for aluminium cable with max. 50 mm²
cross-section (Cat. No. 4 063 10)
. Sealable screw cover (Cat. No. 4 063 04)
Signalling auxiliaries:
. Auxiliary contact (0.5 module, Cat. No. 4 062 58)
. Fault signalling contact (0.5 module, Cat. No. 4 062 60)
. Auxiliary contact that can be changed into fault signalling contact
(0.5 module, Cat. No. 4 062 62)
. Auxiliary c fault signalling contact that can be changed into
2 auxiliary contacts (1 module, Cat. No. 4 062 66)
Control auxiliaries:
. Shunt trip (1 module, Cat. No. 4 062 76, 2 78)
. Undervoltage release (1 module, Cat. No. 4 062 80, 82)
. Stand-alone release for N/C push-button
(1.5 module, Cat. No. 4 062 87)
Motor driven control modules:
.
Motor-driven control module (1 module, Cat. No. 4 062 91)
. Motor-driven control module with integrated automatic reset
(2 modules, Cat. Nos. 4 062 93, 95)
Possible combinations of auxiliaries and RCBOs:
. The auxiliaries are installed to the left of the RCBOs
. Maximum number of auxiliaries = 3
. Maximum number of 1 module signalling auxiliaries = 2
. Maximum number of control auxiliaries
(Cat. Nos. 4 062 76 to 4 062 87) = 1
. The control auxiliary trip (Cat. Nos. 4 062 76 to 4 062 87) must
mandatorily be placed to the left of the signalling auxiliaries (Cat.
Nos. 4 062 58 to 4 062 66) where the auxiliaries from these 2
families are connected to the same RCBO
Sealing:
. Possible in the open or closed positions
Locking options:
. Via padlock 5 mm in diameter (Cat. No. 4 063 13) or padlock
6 mm in diameter (Cat. No. 227 97) and padlock support (Cat. No.
4 063 03)
Installation software:
. XL PRO
3
9. SAFETY
. For your safety your electrical installation is equipped with residual
current protection and this must be tested periodically. In the
absence of any national regulations on the time period required for
this, Legrand recommends that this test be carried out every month:
press the "T" test button, the device should trip. Please call an
electrician immediately if this does not happen as the safety level of
your installation has been reduced
. The presence of residual current protection does not remove the
need to observe all the precautions associated with using electrical
energy.
Technical data sheet: F01315EN/03
Updated on: 30/05/2018
Created on: 27/05/11
