background image

11/16 

 

ELIOT Kit STOP&GO Connected 

 

Cat. N°: 4

 149 54

 

 

 

5. GENERAL CHARACTERISTICS 

(continued)

 

Plastic materials:  

. Self-extinguishing polycarbonate. 
. Heat and fire resistant according to IEC/EN 60695-2-12, glow-wire 

test at 960°C.

 

. Classification UL 94 / IECEN 60695-11-10: V1 

Ambient operating temperature: 

. Min. = - 

5 °C / Max. = + 60 °C.

 

Ambient storage temperature: 

. Min. = - 

25 °C / Max. = + 60 °C.

 

Protection Index: 

. Protection index of terminals against direct contacts: 
IP2X (IEC/EN 60529). 
. Protection index of terminals against solid and liquid bodies (wired 
device): IP 20 (IEC/EN 60529). 
. Protection index of the front face against solid and liquid bodies: IP 
40 (IEC/EN 60529). 
. Class II, front panel with faceplate. 

Resistance to sinusoidal vibrations: 

. According to IEC 60068-2-6. 
. Axis: x, y, z. 

. Frequency range: 5÷100 Hz; duration 90 min.

 

. Displacement (5÷13.2 Hz): 1mm

 

. Acceleration (13.2÷100 Hz): 0.7g (g=9.81 m/s

2

). 

Average weight per device: 

 

Weight (kg) 

Stop&Go 

0,174 

Wi-Fi Interface with external antenna 

0,081 

Power Supply module 

0,069 

Supply patch cord 250 mm 

0,005 

Volume when packed: 

. 1,00 dm

3

Consumption: 

. Stop&Go 
  Values at 230 VAC 
  Standby power consumption: <1,5 VA 
  Maximum power consumption:  <20 VA rms (<80VA peak) during 
resetting 
. Wi-Fi Interface 
  Value at 12 VDC 
  0,236 W 
. Power supplier 
  Value at 230 VAC 
  Maximum power consumption:  <20 VA rms  
 

 

 

 

 

Technical data sheet: F02465EN/01 

Updated: 28/03/2019 

Created: 06/10/2016 

 

 

 

Summary of Contents for 4 149 54

















Reviews: