background image

2 - Operation

14

You can deactivate (reactivate) one or more zones at any time. This 
will allow you to personalise the burglar-alarm operation according to 
your needs.

For instance, if you want to have protection even if you’re not at home, 
you can deactivate the infrared detector zones, leaving the outer zones 
(entrance door and windows) active. This will allow you to move around 
freely inside your house without making any alarms go on and without 
giving up safety.

The zones in which your burglar alarm is split into appear in the fi rst 
line of the display.

The active zones are shown in a dark box.

The following example shows the system made up of 4 zones, all active; 
zone 3 is deactivated.

Activating - deactivating the zones

 

The zones (max. 4) of the system are all 
active (e.g. 1-2-3-4)

Press the corresponding key on the Unit 
keypad to deactivate zone 3

The display shows zone 3 without the 
dark box (deactivated)

Press the key  

 

Type in the user code (basic 00000) or 
an enabled numeric code

With user code

 

3

1

2

3

5

6

9

8

7

0

4

 1 2 3 4

 15/11/08             15:05

 1 2 

3

 4

 15/11/08             15:05

Summary of Contents for 5739 46





























Reviews: