No: 341168 1/20
Pass & Seymour
®
Occupancy/Vacancy Sensor Switch
Interrupteur à détection de présence/Interrupteur détecteur d’inoccupation
Interruptor de sensibilidad a la ocupación/Interruptor con sensor de “habitación vacía”
Incandescent/ELV: 600W ; CFL/LED: 450W; MLV: 600VA; ELV: 5A; Motor: 1/6 hp
Installation Instructions • Notice d’Installation • Instrucciones de Instalación
Catalog Number(s) • Numéro(s) de Catalogue • Les Numéros de Catalogue: RRW600U, RRW600UV2
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION AND OPERATION
The RRW600U occupancy and vacancy sensor is designed to replace a
standard light or fan switch and are suitable for use in new construction
or retrofit/replacement applications. The sensor uses passive infrared
technology to sense human motion in a space and turn the light OFF when
the room is vacant. It is ideal for applications in a home where there is a
direct line of sight from the sensor to the room, including bedrooms and
family/living rooms.
Occupancy Mode:
The load will automatically come ON when motion is detected, and turn
OFF automatically, at the desired time delay, if no motion is detected. If the
load is manually turned OFF, and motion is detected within 30 seconds,
the load will remain OFF until no motion has been detected for 30 seconds.
It can then automatically turn ON again once it detects motion. The
RRW600U allows the load to be turned ON manually as well, and turn OFF
automatically at the desired time delay, if no motion is detected.
Vacancy Mode:
In this mode, the load is required to be turned ON manually, and will
turn OFF at the desired time delay, if no motion is detected. If motion is
detected within 30 seconds after it automatically turns OFF, the RRW600U
automatically turns the load back ON.
USER SETTINGS
Table 1 – Time Delay Setting
Setting
Status
From User
(Input to the device)
LED or LOAD State
(Acknowledgement
from the device)
Result
Time Delay
Adjustment
Mode – To
change the
amount of time
before the
sensor switch
turns off after
last movement
Initiate
With the load ON or OFF,
hold down the ON/OFF
button for 10 seconds
then release
LED will blink 5 times
and then turn off
Enters
Time Delay
Adjustment Mode
Activate
Push down the ON/OFF
button first time.
LED flashes quickly two
times per 1.5s.
Set the time delay to
5 Minutes
Push down the ON/OFF
button second time
LED flashes quickly
three times per 1.5s.
Set the time delay to
10 Minutes
Push down the ON/OFF
button third time
LED flashes quickly four
times per 1.5s.
Set the time delay to
15 Minutes
Push down the ON/OFF
button fourth time
LED flashes quickly five
times ON per 1.5s.
Set the time delay to
30 Minutes
Push down the ON/OFF
button fifth time
LED flashes quickly one
time per 1.5s.
Set the time delay
to 30 Seconds
Save/Exit
Hold down the ON/OFF
button for 10 seconds
then release
LED will blink 5 times
and then turn off
Save/Exit Time
Delay Adjustment
Mode
Table 2 – RRW600U Occupancy/Vacancy Mode Adjustment
Setting
Status
From User
(Input to the device)
LED or LOAD State
(Acknow ledgement
from the device)
Result
Working Mode
Setting: to
Change between
Occupancy Mode
(Auto on) and
Vacancy Mode
(Manual On)
Initiate
With the load ON or OFF,
hold down the ON/OFF
button for 15 seconds
then release
LED will blink 5 times
and then turn off
Enters
Working Mode
Setting Mode
Activate
Push down the ON/OFF
button first time
LED flashes quickly
two times ON per 1s.
Set the Working
Mode to vacancy
sensor
Push down the ON/OFF
button second time
LED flashes quickly
one time ON per 1s.
Set the
Working Mode
to occupancy
sensor
Save/Exit
Hold down the ON/OFF
button for 15 seconds
then release
LED will blink 5 times
and then turn off
Save/Exit
Working Mode
Setting Mode
The RRW600U has an onboard indicator LED located at the top of the unit This
indicator is used to show when motion is detected. The LED is also used while
programming the RRW600U and indicates STATUS during power up. The LED
is further used to indicate a malfunctioning unit. Both Occupancy and Vacancy
Modes can be programmed/selected to function with or without the LED
indicator if preferred by the user.
Table 3 – Status LED Enable/DIsable
Setting
Status
From User (Input to
the device)
LED or LOAD State
(Acknow ledgement
from the device)
Result
Enable and
disable the
status LED
indicator
When the
LED is
Enabled
With the load ON or
OFF, hold down the
ON/OFF button for
25 seconds
LED will blink 5 times
and then turn off
LED will Disable: locator light
will be in an “On State” when
the load is off and will not blink
when motion is detected; the
locator light will be in an “Off
State” when the load is on and
will not blink when motion is
detected
When the
LED is
Disabled
With the load ON or
OFF, hold down the
ON/OFF button for
25 seconds
LED will blink 5 times
and then turn off
LED will Enable: locator light
will be in an “On State” when
the load is off and will not blink
when motion is detected; the
locator light will be in an “Off
State” when the load is on
and will blink when motion is
detected.
COVERAGE AREA
The RRW600U has a maximum
coverage range of 180 degrees
and a coverage area of 600 square
feet (56 square meters). The sensor
must have a clear and unobstructed
view of the coverage area. Objects
blocking the sensor’s lens may
prevent detection thereby causing
the light to turn off even though
someone is in the area.
Windows, glass doors, and other
transparent barriers will obstruct
the sensor’s view and prevent
detection.
INSTALLATION & WIRING
1. Prepare the switch box.
After the power is turned off at the circuit breaker box, remove the existing wall
plate and mounting screws. Pull the old switch out from the wall box.
2. Identify the type of circuit.
Single Pole
In a Single Pole Circuit (see Figure
2), two single wires connect to two
screws on the existing switch. A
ground wire may also be present
and connected to a ground terminal
on the old switch.
3-Way
In a 3-way circuit (see Figure 3),
there will be [2 runners and
1 common] for both switches
involved.
CAUTION For your safety:
Connecting a proper ground to the sensor provides
protection against electrical shock in the event of certain fault conditions. If
a proper ground is not available, consult with a qualified electrician before
continuing installation.
3. Prepare the Wires.
Tag the wires currently connected to
the existing switch, so that they can be
identified later. Disconnect the wires. Make
sure the insulation is stripped off the wires
to expose their copper cores to the length
indicated by the “Strip Gage,” in Figure 3a.
4. Wire the sensor.
1-pole configuration:
Twist existing wires together with the wire leads on the RRW600U sensor as
indicated below. Cap them securely using the wire nuts provided. See Figure 4.
• Connect the green or non-insulated (copper) GROUND wire from the circuit
to the green ground terminal on the RRW600U. Make sure there is a solid
ground connection.
• If neutral is available in the
box, connect to the Blue and
White striped (signal) wire
on the RRW600U. In cases
of retrofit or replacement
where no neutral is present,
connect the signal wire to
ground.
• Connect the power wire from
the circuit (HOT) to the black
wire on the RRW600U.
• Connect the power wire
to the lamp or fan (LOAD)
to the red wire on the
RRW600U.
Multilocation configuration
(using existing companion
3-way switch): see Figure 5.
• Connect the green or non-insulated (copper) GROUND wire from the circuit
to the green ground terminal on the RRW600U. Make sure there is a solid
ground connection.
• If neutral is available in the box, connect to the Blue and White striped
(signal) wire on the RRW600U. In cases of retrofit or replacement where no
neutral is present, connect the signal wire to ground.
• Connect the power wire from the circuit (HOT) to the black wire on
the RRW600U.
• Connect the power wire to the lamp or fan (LOAD) to the red wire on
the RRW600U.
• Connect one of the runner wires to the yellow wire of the RRW600U.
• For the companion switch, connect the chosen runner wire (presently
hooked up to the yellow wire of the RRW600U) to the common of the 3-way
companion mechanical switch.
• Connect one of the poles of the companion 3-way switch to ground.
• For the remaining pole of the companion 3-way switch, do not connect to
anything, but still cap off with a wire nut.
common
commun
común
H1 NC
H2
Line
Ligne
Linea
Black
Noir
Negro
Yellow
Jaune
Amarillo
Green
Vert
Verde
Red
Rouge
Rojo
Load
Charge
Carga
Ground
Terre
Tierra
Neutral
Neutre
Neutro
Blue w / White Stripes
Neutral or Ground (See Instructions)
Figure 5: 3-Way Configuration / Figure 5 : Configuration à 3 voies
Figura 5: Configuración de 3 vías
Multilocation configuration (using up to 5 units, maximum wire length of
100 ft between companion unit and unit connected to the load):
see Figure 6.
• Connect the green or non-insulated (copper) GROUND wire from the circuit
to the green ground terminal on the RRW600U. Make sure there is a solid
ground connection.
• If neutral is available in the box, connect to the Blue and White striped
(signal) wire on the RRW600U. In cases of retrofit or replacement where no
neutral is present, connect the signal wire to ground.
• Connect the power wire from the circuit (HOT) to the black wire on
the RRW600U.
• Connect the power wire to the lamp or fan (LOAD) to the red wire on
the RRW600U.
• Connect one of the runner wires to the yellow wire of the RRW600U.
• For the companion RRW600U, connect the chosen runner wire (presently
hooked up to the yellow wire of the 1st RRW600U) to the yellow wire of the
companion RRW600U.
• Repeat for additional RRW600U units.
5. Put the RRW600U in the wall box. Position the lens above the ON/OFF
button (lens at top, button at bottom). Secure it to the wall box with the
screws provided.
6. Make any necessary adjustments. See the SENSOR ADJUSTMENT section
for information.
7. Attach the new cover plate.
8. Restore power to the circuit. Turn on the breaker or replace the fuse.
INITIAL POWER UP DELAY
There is an initial warm-up (about 1 minute) and calibration period the first
time power is applied to the unit and after the load is replaced. The warm-up
sequence also occurs as a result of a power failure, and any time power to the
unit is cycled.
CHANGING THE COLOR OF THE UNIT
1. Remove the wallplate.
2. Firmly grasp the edges of
the front cover directly below
the lens where it says “open.”
Push in one side first until it
pops out, then the other side.
Remove front cover from the unit
(see Figure 7).
3. Take the new color front cover,
place the top peg in first then
snap in each side one at a
time (see Figure 9).
TROUBLESHOOTING
Status LED is enabled but not blinking and the load will not turn ON:
• Check the circuit breaker to be sure it is functioning.
• Check to make sure that the device is properly grounded. This device will not
function if it is not grounded.
Load will not turn ON:
Press ON/OFF button. The load should turn ON. If not:
• Check the light bulb and/or motor switch on the fan mechanism.
• Turn OFF power to the circuit then check wire connections.
• For further assistance call 800.223.4185 for technical support.
Load will not turn OFF:
Note: The time delay can be set from 30 seconds to 30 minutes. Ensure that
the time delay is set to the desired delay and that there is no movement within
the sensor’s view for that time period.
• To quickly test the unit for proper operation, turn the time delay to minimum
and move out of the sensor’s view. Lights should turn off after 30 seconds.
• Press the ON/OFF button. If load does not turn off, turn off power to the
circuit then check wire connections.
• For further assistance call 800.223.4185 for technical support.
25'
(7.6m)
12'
(3.7m)
Figure 1: Sensor Coverage Area
Figure 1 : Zone de portée du détecteur
Figura 1: Área de cobertura del sensor
Figure 3: 3-Way
Figure 3: Trois voies
Figura 3: 3 Vías
READ AND SAVE THESE INSTRUCTIONS
To be installed by a certified electrician or other qualified person.
WARNING
– To prevent severe shock or electrocution, always turn
poweroff at the service panel before installing this product, working on the
circuit, or changing a lamp.
CAUTION
• Do not connect this product to a power source other than 120VAC,
60Hz.
• Use copper wire only.
Specifications
Load..........................................Single Pole or 3 Way
Time Delay ...............................30 Seconds to 30 Minutes
Environment .............................Indoor Use Only
Tools Needed
Insulated Screwdriver, Wire Strippers
LIRE ET CONSERVER CES INSTRUCTIONS
Doit être installé par un électricien certifié ou une autre personne qualifiée.
AVERTISSEMENT
– Pour éviter tout choc électrique ou une électrocution,
toujours couper l’électricité au niveau du panneau d’alimentation avant
d’installer cette unité, de travailler sur le circuit électrique ou de changer
une lampe.
AVERTISSEMENT
• Ne brancher ce produit qu’à une source d’alimentation de 120 V c.a.,
60 Hz.
• N’utiliser que des fils en cuivre.
Spécifications
Charge ......................................Unipolaire ou à 3 voies
Temporisation ...........................30 secondes à 30 minutes
Environnement .........................Utilisation en intérieur uniquement
Outils nécessaires
Tournevis isolé, dénudeurs de fil
LEA Y CONSERVE ESTAS INSTRUCCIONES
Para ser instalado por un electricista certificado o persona competente.
ADVERTENCIA
– Para evitar descargas eléctricas serias o electrocución,
antes de instalar, trabajar en el circuito o cambiar una lámpara de este
atenuador apague siempre el suministro eléctrico en el panel de servicio.
PRECAUCIÓN
• No conecte este producto a una fuente de alimentación que no sea de
120 V AC, 60Hz.
• Use solamente cables de cobre.
Especificaciones
Carga ........................................Polo único o de 3 vías
Tiempo de demora ...................30 segundos a 30 minutos
Entorno .....................................Solo uso en interiores
Herramientas necesarias
Destornillador aislado, pelacables
Figure 6: Multilocation Configuration
Figure 6 : Configuration à plusieurs emplacements
Figura 6: Configuración de ubicación múltiple
NC
Black
Noir
Negro
Yellow / Jaune / Amarillo
Green
Vert
Verde
Ground
Terre
Tierra
Line
Ligne
Linea
Load
Charge
Carga
Line
Ligne
Linea
Red
Rouge
Rojo
Neutral
Neutre
Neutro
Line
Ligne
Linea
Black
Noir
Negro
Green
Vert
Verde
Ground
Terre
Tierra
Red
Rouge
Rojo
Blue w/White Stripes
Blue w/White Stripes
Neutral or Ground (See Instructions)
Neutral or Ground (See Instructions)
Time
Dela
y
Motion
Blink
OFF
30sec.
30min
.
5min.
10min
.
20min
.
11543r
1
Figure 9: Replace Front Cover
Figure 9 : Remplacement de
la protection avant
Figura 9: Reemplace la cubierta frontal
RRW600U
Figure 2:
Single Pole
Figure 2: Pôle simple
Figura 2: Polo único
Line
Ligne
Linea
NC
Black / Noir / Negro
Yellow / Jaune / Amarillo
Green / Vert / Verde
Red
Rouge
Rojo
Load
Charge
Carga
Ground
Terre
Tierra
Neutral
Neutre
Neutro
Blue w / White Stripes
Neutral or Ground (See Instructions)
Figure 4: Single Pole Configuration
Figure 4 : Configuration unipolaire
Figura 4: Configuración del polo único
3-Way
In a 3-Way circuit, identify the Common/
Hot wire – connected to the terminal
marked Common or the odd-colored
terminal screw.
Trois voies (3-Way)
Pour un circuit à trois voies, identifier le
câble de commun/courant raccordé à la
borne marquée « Commun » ou à la vis
de borne de couleur différente.
3 vías
En un circuito de 3 vías, identifique el
cable Común/Vivo: conectado al terminal
marcado como Común o al tornillo del
terminal de color diferente.
Strip Gage
1/2"
12.7mm
Figure 3a: Wire Stripping
Figure 3a : Dénudage des fils
Figura 3a: Pelado de cables
Strip Gauge,
Borne à vis
Traseros para cables
1/2"
12.7mm
