LEGRAND STARK 10 kVA Installation And User Manual Download

Page: 3 / 52

Table Of Content

1.SAFETY

1.1 SAFETY NOTES ............................................................................................................. 4

1.2 SYMBOLS USED IN THIS GUIDE .................................................................................. 4

2. MAIN FEATURES ....................................................................................................................5

2.1 SUMMARIZATION .......................................................................................................... 5

2.2 FUNCTIONS AND FEATURES ....................................................................................... 5

2. INSTALLATION .......................................................................................................................6

3.1 UNPACK CHECKING ..................................................................................................... 6

3.2 CABINET OUTLOOK ...................................................................................................... 6

3.3 LCD CONTROL PANEL .................................................................................................. 8

3.4 INSTALLATION NOTES ................................................................................................. 8

3.5 EXTERNAL PROTECTIVE DEVICES ............................................................................... 9

3.6 POWER CABLES ......................................................................................................... 10

3.7 POWER CABLE CONNECT .......................................................................................... 11

3.8 BATTERY CONNECTION ............................................................................................. 12

3.9 UPS PARALLEL INSTALLATION ................................................................................. 14

3.9.2 PARALLEL CABLE INSTALLATION ....................................................................... 15

3.9.3 REQUIREMENT FOR THE PARALLEL SYSTEM ..................................................... 15

3.10 COMPUTER ACCESS ................................................................................................. 15

4. OPERATION ..........................................................................................................................17

4.1 OPERATION MODES ................................................................................................... 17

4.2 TURN ON/OFF UPS ..................................................................................................... 20

4.2.1 RESTART PROCEDURE ......................................................................................... 20

4.2.2 TEST PROCEDURE ................................................................................................ 21

4.2.3 MAINTENANCE BYPASS ....................................................................................... 21

4.2.4 COLD START PROCEDURE ................................................................................... 22

4.2.5 SHUT DOWN PROCEDURE ................................................................................... 23

4.2.6 PARALLEL SETTING ............................................................................................. 23

4.3 THE LCD DISPLAY ....................................................................................................... 26

4.4 PARAMETERS SETTING ............................................................................................. 30

4.4.1 MODE SETTING ..................................................................................................... 30

4.4.2 OUTPUT VOLTAGE SETTING ................................................................................. 31

4.4.3 FREQUENCY SETTING .......................................................................................... 31

4.4.4 BATTERY CAPACITY SETTING .............................................................................. 32

4.4.5 BATTERY QUANTITY SETTING .............................................................................. 32

4.4.6 BYPASS VOLTAGE UPPER LIMIT SETTING........................................................... 32

4.4.7 BYPASS VOLTAGE LOWER LIMIT SETTING .......................................................... 33

4.4.8 BUZZER MUTE SETTING ....................................................................................... 33

4.4.9 PERIODICAL BATTERY SELF-TEST SETTING ....................................................... 34

4.4.10 BATTERY TEMPERATURE COMPENSATION SENSOR SWITCH SETTING ......... 34

4.4.11 DEVICE ADDRESS SETTING ................................................................................ 35

4.4.12 PARALLEL ID SETTING ....................................................................................... 35

4.4.13 PARALLEL QUANTITY SETTING .......................................................................... 36

4.4.14 PARALLEL REDUNDANCY QUANTITY SETTING................................................. 36

4.5 PARALLEL SYSTEM COMMISSIONING ...................................................................... 37

4.6 DISPLAY MESSAGES/TROUBLESHOOTING ............................................................... 38

4.7 OPTIONS ..................................................................................................................... 41

APPENDIX 1 SPECIFICATIONS .................................................................................................42

APPENDIX 2 PROBLEMS AND SOLUTION ................................................................................45

APPENDIX 3 RS232 COMMUNICATION PORT DEFINITION .......................................................46

APPENDIX 4 RS485 COMMUNICATION PORT DEFINITION .......................................................47

APPENDIX 5 BAT_T COMMUNICATION PORT DEFINITION ......................................................48

APPENDIX 6 OPTIONAL PORT DEFINITION .............................................................................49

APPENDIX 7 REPO INSTRUCTION............................................................................................50

Summary of Contents for STARK 10 kVA





















































Search results

Summary of Contents for STARK 10 kVA

Reviews:

Related manuals for STARK 10 kVA

Brands by name

Popular brands

LEGRAND STARK 10 kVA, Installation And User Manual

Search results

Summary of Contents for STARK 10 kVA

Reviews:

Related manuals for STARK 10 kVA

Brands by name

Popular brands