WWW.LEGRAND.US/WATTSTOPPER - IS-00709-F Commercial Enclosure Solutions — MODEL: LCAP44A & LCA Main Lug
page 3 of 8
LCAP Panels with Main Lug Panel OPTION
LCAP44/A/LO/CB Panels with Main Lug Panel OPTION
Main Lug Circuit Breaker Option
The LCAPA and LCAPM series enclosures can be configured as a
load
feed
through panel (LCAP PANEL only) or as main lug panels with the addition of load
circuit breakers below the load control feed through compartment. Main lug
options can also contain a main breaker. The Main Lug option is available for the
LCAP
ALO
and LCAP
MLO/SLO
series panels – see the
LCAP32/44/M/S
install
sheet. The circuit breaker options are based on the panel configuration, number
and type of loads,
and circuit breaker rating requirements. Once the main lug
panel and circuit breaker options are selected the panel is built and prewired
*
in
the factory and delivered to the project ready to be installed.
*NOTE:
Panels with GFI breakers
: GFI breakers are not installed or
pre-wired and are shipped separately.
Applications
The LCAP44A is designed for medium to large spaces requiring control of up to
24 low voltage PWM lighting circuits, 24 low voltage 010V DC lighting circuits,
and 24 120-277VAC relay lighting circuits. The built-in integration and networking
capabilities of the LCAP44A easily meet requirements in spaces needing multiple
types of lighting, and other automation integration systems using this panel.
Adding an Equinox 41 or 73 touchscreen to the project allows the facility
manager or end user to create, change, and manage scenes, schedules, and
user profiles.
Features
Modular LCAP load section; pre-configured solution from the factory. Just
connect line voltage and load wires.
Pre-configured Main Lug Panel solution options.
System is expandable using other LCAP series primary or secondary panels
and LCAP Main Lug / Circuit Breaker options.
Can be configured with emergency circuits for emergency lighting.
Connects to InFusion Controller system via Ethernet or Station Bus.
Up to 24 dry contact inputs; 12 of the contacts may be used for, system
powered, light sensors or occupancy sensors.
Dimmers have programmable start/stop and dimming curve adjustment
features to customize dimming linearity.
Simple programming from a single software solution - Design Center.
Adding one BACnet enabled controller to a system allows the entire system
to be controlled through BACnet.
Main Lug Panel options range from 18 to 36 circuits, 208-480V, and 10kAIC
to 65kAIC and may be configured with a main breaker option.
Setup In Design Center
Understanding LCAP and Main Lug panels
:
LCAP panels with the Main Lug option is a larger enclosure that holds the
traditional LCAP components in the upper section of the enclosure and
includes a breaker section in the lower section of the enclosure.
LCAP panels with the Main Lug option are built in Design Center the same
way as standard LCAP panels. The only difference is the Main Lug option
has been selected. Follow the steps below to create an LCAP panel with the
Main Lug option selected.
1. In
Design Center | Object Explorer
select
Vantage Objects,
Enclosures, Commercial,
LCAP model,
o
LCAP44A-KIT (Main Lug),
2.
Right click in the enclosure and select
Populate
to automatically add LVOS-PWM
stations
in the enclosure or select LVOS-
PWM stations
and drag into the enclosure
as wanted. (It is not possible to drag an
LVOS-PWM station below a blank station
position in an LCAP enclosure – fill
enclosure from left to right / top to bottom.
Notice that breakers are automatically
added to the
Main Lug
section of the
enclosure as LVOS-PWM stations are
added.
3.
It is possible to add additional breakers in
the Main Lug section by right clicking
below existing breakers and selecting Add
Breaker until the maximum number of
breakers allowed is reached.
4.
Select the Main Lug section of the
enclosure and change the type to
MCB
to
add a Main Breaker option or leave as
MLO
for standard load breakers only.
LCAP44ALO/MLO/MCB Series Specifications
Specifications
LCAP44ALO/MLO
LCAP44ALO/MCB
Cabinet / Panel Cover Dimensions HWD
68.0” x 24.0” x 4.75”
172.72cm x 60.96cm x 12.06cm
77.0” x 24.0” x 4.75”
195.58cm x 60.96cm x 12.06cm
Breakers
Up to 18
Up to 36
Main Lug Panel Door Dimensions HWD
16” x 12.5” x 0.75”
40.64cm x 31.75cm x 1.9cm
23” x 19” x 0.75”
58.42cm x 48.26cm x 1.9cm
Weight Enclosure with Cover
165 - 175 lbs / 74.84 – 79.38 kg
170 - 180 lbs / 77.11 – 81.65 kg
LCAP Panel Door Dimensions HWD
40.5” x 16.0” x 0.75” / 102.87cm x 40.64cm x 1.9cm
Panel Insert HWD
42” x 21” x 4.175” / 106.7cm x 53.3cm x 10.6cm
Weight Panel Insert
M-23 lbs. 10.43 kg
Number of LVOS-0-10-PWM
*
stations
Up to 6
Analog, 0-10DC/LV — Max. Outputs
Up to 24
PWM, LV — Max. Outputs
Up to 24
HV Relay 120-277 VAC — Max. Outputs
Up to 24
Enclosure Finish
Galvanized Steel
Door Finish
Black - Powder Coated
Cover
vented, hinged
Wire
copper wire, MIN. of 80°C / 176°F insulation
Ventilation
maintained 36” front clearance
Ambient Operating Temp.
0-40°C / 32-104°F
Ambient Oper. Humidity
5-95% non-condensing
UL, CUL, and CE listed
yes
