background image

S a n ta Clara, CA 95050

8 0 0 . 8 7 9 . 8 5 8 5

Specifications

Vo l tages: 

UW-100 & UW-200  . . . . . . . . . . . . .1 2 0 / 2 3 0 / 2 7 7 VAC, 50/60Hz
U W - 1 0 0 - 3 4 7  . . . . . . . . . . . . . . . . . . . . . . . . . .3 4 7 VAC, 50/60Hz

Load Limits for each re l a y :

@ 1 2 0 VAC  . . . . . . . . . . . .0-800W tungsten or ballast, 1/6 HP
@230 or 277VAC  . . . . . . . . . . . . . . . . . . . . . . .0-1200W ballast
@ 3 4 7 VAC  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0-1500W ballast

Load Type Compatibility:

I n ca n d e s cent, fluore s cent, magnetic or ele c t ronic ballast
H o rs e p ower Rating (each re l a y )  . . . . . . . . .1/6 HP @120VAC

Time Delay Adjust m e n t  . . . . . . . . . . . . . . . . . . . .5 to 30 minute s

Wa l k - T h rough Mode  . .3 minutes if no activity after 30 sec.
Te st Mode  . . . 5 sec. at initial power up or DIP switch re s e t

U l t rasonic Adjust m e n t . . .Minimum to Maximum (trimpot), Off

Fre q u e n c y  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 0 k H z

Light Level Adjust m e n t . . . . . . . . . . . . . . . . . . . . . . .8 fc to 180+fc
A le r t s

 . . . . . . . . . . . . . . . . . . . . . .S e le c ta b le Audible & Visible

US Pa tents: 5640113

6 6 1 7 5 6 0 B 2

U W - 1 0 0 / U W - 1 0 0 - 3 4 7 / U W - 2 0 0

U l t rasonic Wall Switc h

O ccupancy Sensor 

U W-100  & UW- 1 0 0 - 3 4 7

U W- 2 0 0

Summary of Contents for WattStopper UW-100









Reviews: