background image

9

LEHLE GmbH · Germany · www.lehle.com · support@lehle.com

pedance inputs have input impedances 
of around 600 Ω to 10 kΩ.

WHAT IS POSSIBLE
The LEHLE P-SPLIT III can be used to split 
the signal from an electric guitar or elec-
tric bass with passive magnetic pickups to 
two amplifiers, each of which has high-
impedance inputs. Please use the short-
est, best-quality possible cables for this 
purpose. You will hear the 100% original 
signal on both amps.

Instead of an amplifier, you can also split 
the signal to the Hi-Z input of a sound 
card.

It’s important to remember: a high-im-
pedance signal can be passively split if 
you connect only high-impedance inputs.
You can split a low-impedance signal, 
such as the output from a preamp, e.g. 
the LEHLE SUNDAY DRIVER II or the out-
put from a sound card, to a tube amp 
with a high-impedance input and the low-
impedance input of a power amp. Since 
the signal to be split is a low-impedance 
one, you can connect low-impedance 
and high-impedance inputs behind this if 
you wish - there won’t be any problems!

WHAT IS NOT POSSIBLE
Audible sound losses will occur if you use 
long cable routings from the passive gui-
tar to the splitter and from the splitter to 
the amps. The sum of all cable lengths to 

the splitter and to the amps should gener-
ally not be more than 10m. 
Your individual taste will ultimately de-
cide, however.
Splitting your high-impedance instrument 
signal to a low-impedance input, such as 
the line input of a mixing desk, for exam-
ple, and to a high-impedance input on 
a tube amplifier using the LEHLE P-SPLIT 
III will result in the high-impedance input 
being attenuated by the low-impedance 
input of the mixing desk. The signal will 
become significantly quieter and will lose 
presence. 
Solution: these problems can be effec-
tively eliminated by connecting a preamp 
or a buffer, which will convert the high-
impedance to a low-impedance signal, in 
the signal path.
The LEHLE SUNDAY DRIVER II, for exam-
ple, can be used here.

INPUT

INPUT

DIR

DIR

Hi-Z

Hi-Z

Low-Z

Hi-Z

Low-Z

Hi-Z

Hi-Z

Hi-Z

Hi-Z

Hi-Z

Low-Z

Hi-Z

Low-Z

Hi-Z

Low-Z

Low-Z

Hi-Z

Hi-Z

Low-Z

Low-Z

Low-Z

Low-Z

Low-Z

Low-Z

ISO

ISO

!
!
!

Summary of Contents for 1027
























Reviews: