background image

BDA-M400_SV_GB 1

1-2015

3

SAFETY PRECAUTIONS

U

U

On changing the batteries, ensure correct battery polarity and position!

U

U

Dispose of spent batteries in the proper manner.

U

U

Do not heat batteries, take them apart or short-circuit them.

U

U

Never throw batteries into fire.

U

U

The batteries must not be charged.

U

U

Keep batteries out of children‘s reach.

U

U

Any person swallowing batteries must seek immediate medical advice.

U

U

Damaged and/or leaking batteries may cause acid burns and / or poisoning.

ADVICE ON OPERATION AND CARE

U

U

  Do not pour any liquids into or over any of the system‘s components and never immerse the 
components in liquids.

U

U

Transmission / reception range as well as reception quality may be affected by the building‘s structure, 
sources of electronic interference or superimposed frequencies.

U

U

The receiver should not be exposed to direct sunlight.

U

U

Clean the system with a clean, soft, damp cloth only.

U

U

Do not use any cleaning products containing abrasives or solvents, such as glass, thinner, alcohol, 
benzene or ammonia, as they may react adversely with the enclosure.

U

U

Treating any of the electronic and mechanical components improperly or in any way other than 
described in this user manual may lead to malfunctions.

NOTE

Our locks and locking systems can basically be used together with mechanisms made by other
manufacturers, but their compatibility must be checked by the processor in each individual case.
We cannot accept any liability for damage or losses due to incompatibility.

TECHNICAL SPECIFICATIONS

U

#

To operate the system there must be a line of vision between transponder and receiver.

U

#

The distance between the furniture locks must be at least 50 cm.

U

#

Frequency: 25KHz. Be sure to observe national legislation on permissible wireless frequencies.

U

#

The average transmission range of the transponder is approx. 30 cm. Depending on the structural 
conditions, the transmission/reception range may be limited or significantly increased.

U

#

To program and start the system please refer to the system manual from Firma SimonsVoss 
Technologies GmbH. www.simons-voss.com

U

#

Power supply for control electronics: battery type: 2x AA mignon cell, alkaline 1.5V.

U

#

NiCd, NiMH or other rechargeable batteries as well as zinc-carbon or lithium batteries must not be 
used.

Temperature range: 

Operation: 

  +5 °C to +40 °C in 30% to 80% relative air humidity, non-condensing. 

In storage:

   -25 °C to +70 °C in 30% to 80% relative air humidity, noncondensing.

All other aspects are subject to the technical information and regulations issued by
SimonsVoss Technologies GmbH in Munich. www.simons-voss.com

Summary of Contents for M400









Reviews: