background image

BD

A M410 T

A03 / 2019-09 (GB)

3

Power supply

Battery type: 1 x CR123A

Operating temperature

-5 °C to +60 °C 

Storage temparature

-25 °C to +70 °C

Type designation

Lock M410: SLI2CBM6
Keypad TA03: MAIIC3M6

 

SAFETY PRECAUTIONS

 

U

 Pack the battery to transport the lock in such a way, that no short circuit can occur (explosion and fire hazard).

 

U

On changing the battery, ensure correct battery polarity and position.

 

U

Dispose of spent batteries and packaging material in the proper manner (see page 20, „Disposal“)..

 

U

Do not heat batteries, take them apart or short-circuit them.

 

U

Never throw batteries into open fires.

 

U

The battery must not be charged.

 

U

Keep the battery and packaging material out of children’s reach.

 

U

Any person swallowing batteries must seek immediate medical advice.

 

U

Damaged or leaking batteries may cause acid burns and/or poisoning.

CARE & MAINTENANCE

 

U

Protect all system components from moisture.

 

U

Clean the locking system with a clean, soft, damp cloth only.

 

U

Do not use any aggressive detergents containing abrasives or solvents. Glass cleaners, thinners, alcohol, benzene 
or liquids containing ammonia are not suitable for cleaning purposes.

 

U

Treating any of the electronic and mechanical components improperly or in any way other than described in this 
user manual may lead to malfunctions.

 

U

Replace the battery in good time, but at the latest when the visual battery warning on the keypad lights up.

!

TECHNICAL SPECIFICATIONS

Summary of Contents for M410





















Reviews: