Page 48
Step 83
Attach
E2 Long Angles Braces
to
SB1
Swing Beam Support
with 3/8” X 6 ½” Hex
Bolt, 3/8” Lock Washer, 3/8” Flat Washer and
3/8” Spike T-Nut (per diagram). Attach
H1
Swing Beam Ground Board
to E2 Angle
Braces with 5/16” X 2” Lag Screws, Lock
Washers and Flat Washers. Attach
E10
Swing Beam Support
with 5/16” X 2 ½” Lag
Screws, Lock Washers, Flat Washers to SB1
and 5/16” X 2” Lag Screws, Lock Washers,
and Flat Washers to E2 Angle Braces.
Step 84
Attach Y1-105G Large Triangle Braces to A1 Beam
(Note: Counter sunk
hole down on beam per diagram)
with 5/16” X 4” Hex Bolts, Flat Washers,
Flat Washers, and 5/16” Lock Nuts. Attach Angle Brace Assembly to Beam
Assembly (per diagram)
Note: Ground board to inside, per diagram.
A1
E2 - Long Angle Brace - 1 Hole - 2 Required
1.375 x 3.375 x 83 [3.49 x 8.57 x 210.82]
A1 - Swing Beam - 11 Holes - 1 Required
3.375 x 5.375 x 92.5 [8.57 x 13.65 x 234.95]
E10 - Swing Beam Support - 4 Holes - 1 Required
1.375 x 3.375 x 40 [3.49 x 8.57 x 101.60]
H1 - Swing Beam Ground Board - 4 Holes - 1 Required
.9375 x 5.375 x 87 [2.38 x 13.65 x 220.98]
SB1 - Swing Beam Support - 3 Hole - 1 Required
3.375 x 3.375 x 47 [8.57 x 8.57 x 119.38]
5/16 X 1-1/4"
HEX HEAD
BOLT
5/16 X 4"
HEX
HEAD
BOLT
5/16 X 2-1/2"
LAG
SCREW
5/16 X 2"
LAG
SCREW
3/8 X 6-1/2"
HEX
HEAD
BOLT
(5/16")
Lock Nut
3/8"
SPIKE TEE
NUT
3/8
INTERNAL
TOOTH
LOCK
WASHER
"
3/8" FLAT
WASHER
5/16"
INTERNAL
TOOTH
LOCK
WASHER
5/16"
SPIKE TEE
NUT
5/16" FLAT
WASHER
E2
SB1
H1
E10
© Copyright Leisure Time Products Inc.
Sky Fort 09-0112
LARGE
METAL TRIANGLE
Y1-105G
A1
Y1-105G
Small Hole
Large Hole
Under side
Bottom
Top
4”
Hex Bolts
Y1-105G
Metal stake installation: measure in 8” from outside
edge of H2 ground board for ground stake location.
Then screw stake into ground using a long screw
driver for leverage until stake is approximately 1 "
down from top of ground board. Now using a 3/8" drill
bit and hole in stake as guide, drill thru ground board
and attach using 1" Phillips Truss Head Bolt, Flat
Washers and Lock Washer with Barrel Nut.
In some cases you may need to dig hole attach stake
to board then fill with cement keeping below ground
level.
FLAT
WASHER
BOLT
LOCK
WASHER
BO
ARD
FLAT
WASHER
BARREL
NUT
5/16"
H2
Step 82
