LeMond Fitness G-Force RT Assembly & Instruction Manual Download

Page: 10 / 12

Attaching the Seat Assembly to the Body

Note:

Install the handlebars and seat bottom before attaching the seat assembly to the body of the bike.

1. Locate the two tabs that are on the top surface of the seat carrier which is located on the seat

track of the body.

2. Located under the seat is a bar that runs the width of the seat. Hook the tabs of the seat carrier

over the bar on the seat assembly. (A)

CAUTION: Be careful not to pinch the wiring for the contact heart rate grips when attaching
the seat assembly to the seat carrier.

3. Lower the seat assembly over the seat carrier and align the holes at the front of the seat assem-

bly with those on the seat carrier. (B)

4. Secure the seat assembly to the seat carrier by sliding (2) flat washers and (2) star washers onto

each of (2) M8x20 screws and tighten with the 6mm hex wrench.

Connecting the Wiring for the Contact

Heart Rate Grips

Once the seat assembly has been attached to the seat

carrier, connect the two wires on the handlebars to

their corresponding wires on the seat carrier.

The connection on each of the two wires is different.

There is only one correct way to make the connection.

Do not try to force the connection.

Summary of Contents for G-Force RT












