background image

3..1  Body

1.  Fold down the sides of the carton base and 

remove the packing material from around the 

bike.

2.  Leave the body of the bike on the carton base 

while the remaining assembly is completed.

CAUTION: Remove the staples completely to 
avoid injury.

3..  Front Stabilizer

1.  Locate the front stabilizer and the unattached wheel.  The front stabilizer already has one wheel 

attached.

2.  Slide the front stabilizer into place at the front of the body frame from the

 left side.  Rotate the 

stabilizer until the set screw is positioned into the alignment notch.  This will align the attach-

ment screw holes of the body and the front stabilizer.  Be careful not to dislocate the plastic 

sleeve at the opposite side of the tubing.  If the sleeve is pushed out of place, remove the stabi-

lizer, replace the sleeve and reinstall the stabilizer.

3.  Secure the front stabilizer by sliding star washers onto each of (2) M8x30 screws and tightening 

with the 6mm hex wrench.

4.  Slide the remaining front wheel onto the end of the front stabilizer and attach the wheel cap.  

Use the alignment pins as a guide to install the wheel cap correctly.

5.  Secure the wheel cap to the wheel with (2) self-tapping screws and tighten with the 3mm 

wrench.

Summary of Contents for G-Force RT













Reviews: