background image

 

FOR YOUR SAFETY do not install or operate this appliance without 

first reading and understanding this manual. Any installation or 

operation of the appliance deviating from that which is stated 

in this manual WILL void the warranty and may be hazardous.

 INSTALLATION AND REPAIR SHOULD ONLY BE DONE BY 

A QUALIFIED SERVICE TECHNICIAN. DO NOT ATTEMPT 

TO SERVICE THE APPLIANCE YOURSELF.

 

Do not make any make-shift compromises during installation.  

Any modification or alteration may result in damage to the ap-

pliance or dwelling and will void the warranty, certification and 

listings of this unit.

 

Failure to use manufacturer provided parts, variations in tech-

niques and construction materials or practices other than those 

described in this manual may create a fire hazard and void the 

limited warranty.

 

This gas appliance must be equipped for the proper fuel type 

and altitude at which it will be operated. Any operation outside 

the parameters outlined in this manual may result in a hazard-

ous condition and will void the warranty. Please carefully read 

the sections pertaining to these subjects and/or be sure your 

appliance is properly equipped.

 Never use solid fuels such as wood, paper, cardboard, coal, or 

any flammable liquids, etc., in this appliance.

 

Any grill, panel, or glass removed for service MUST be replaced 

prior to operating the appliance. Do not operate appliance with 

the glass front removed, cracked or broken. 

 Gold  and  nickel  plated  surfaces  must  be  cleaned  with  glass 

cleaner  and  a  clean  soft  cloth  before  firing  the  first  time  or 

fingerprints will remain permanently. NEVER use brass polish 

to clean gold or nickel, this will remove the plating!!!

 When opening the lower door on the face while the appliance is 

burning, pull at the far left or far right vent openings, because 

the door is hot during operation.

 LHP, its employees, or any of its representatives assume no 

responsibility for any damages caused by an inoperable, inad-

equate, or unsafe condition as a result of any improper operation, 

service or installation procedures, whether direct or indirect.

 

Due to high temperatures, the appliance should be located out 

of traffic and away from furniture and draperies. 

 

En  raison  des  températures  élevées,  l’appareil  devrait  être 

installé dans un endroit où il y a peu de circulation et loin du 

mobilier et des tentures.

Provide adequate clearances around air openings and adequate 

accessibility clearance for service and proper operation. Never 

obstruct the front openings of the appliance.

These appliances are designed to operate on natural or propane 

gas only. The use of other fuels or combination of fuels will de-

grade the performance of this system and may be dangerous.

 

These appliances are designed as supplemental heaters. There-

fore, it is advisable to have an alternate primary heat source 

when installed in a dwelling.

These appliances must not be connected to a chimney or flue 

serving a separate solid fuel burning appliance.

 

These appliances are vented gas appliances. Do not burn wood 

or other material in these appliances.

 

This appliance is only for use with the type of gas indicated on 

rating plate. This appliance is not convertible for use with other 

gases, unless a certified kit is used.

 

Cet appareil doit être utilisé uniquement avec les types de gaz 

indiqués  sur  la  plaque  signalétique.    Ne  pas  l'utiliser  avec 

d'autres gaz sauf si un kit de conversion certifié est installé.

 

Hot while in operation. Do not touch. Severe Burns may result. 

Keep  children,  clothing  furniture,  gasoline  and  other  liquids 

having flammable vapors away.

 

L’appareil  est  chaud  lorsqu’il  fonctionne.  Ne  pas  toucher 

l’appareil. Risque de brûlures graves. Surveiller les enfants. 

Garder les vêtements, les meubles, l’essence ou autres liquides 

produisant des vapeur inflammables loin de l’appareil.

 

This appliance may be installed in an aftermarket, permanently 

located, manufactured home (USA only) or mobile home, where 

not prohibited by local codes.

 

Cet appareil peut être installé dans une maison préfabriquée 

(mobile) déjà installée à demeure si les règlements locaux le 

permettent.

 

Ensure  clearances  are  in  accordance  with  local  installation 

codes and the requirements of the gas supplier.

 

Dégagement conforme aux codes d'installation locaux et aux 

exigences du foumisseunde gaz.

Installation and repair should be done by a qualified service 

person. The appliance should be inspected before use and at 

least annually by a professional service person. More frequent 

cleaning may be required due to excessive lint from carpet-

ing, bedding material, etcetera. It is imperative that control 

compartments, burners and circulating air passageways of the 

appliance be kept clean.

L’installation et la réparation devrait être confiées à un technicien 

qualifié. L’appareil devrait faire l’objet d’une inspection par un 

technicien professionnel avant d’être utilisé et au moins une 

fois l’an par la suite. Des nettoyages plus fréquents peuvent 

être nécessaires si les tapis, la literie, et cetera produisent une 

quantité importante de pous-sière. Il est essentiel que les com-

partiments abritant les commandes, les brûleurs et les conduits 

de circulation d’air de l’appareil soient tenus propres.

Do not use these appliances if any part has been under water.  

Immediately call a qualified, professional service technician 

to inspect the appliance and to replace any parts of the control 

system and any gas control which have been under water.

Ne pas utiliser cet appareil s’il a été plongé, même partielle-

ment, dans l’eau. Appeler un technicien qualifié pour inspecter 

l’appareil et remplacer toute partie du système de commande 

et toute commande qui a été plongée dans l’eau.

Only trim kit(s) supplied by the manufacturer shall be used in 

the installation of this appliance.

Seules les trousses de garniture fournies par le fabricant doivent 

être utilisées pour l’installation de cet appareil.

 INSTALLER:  THESE INSTRUCTIONS ARE TO REMAIN WITH THE 

HOME OWNER!

4

Summary of Contents for CI1500DVF Series



























Reviews: