background image

11

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Top Log

Ports

Install front logs on retainer slots.

Place top log on pin.

Figure 10

Figure 11

s

urround

 p

anels

 i

nstallation

The Medina insert surround panels is made of heavy gage 

steel for durability and, if desired, for the ease of making an 

inside fit in the fireplace.

1.   Remove the speed nuts (A in Figure 12) from the parts 

bag and install (with the flat surface forward) on the 

six holes in the surround brackets - three on each side 

of the insert (B in Figure 12). A flat bladed screwdriver 

may help in installing the nuts.

2.   Install all surround panels and trim with the insert po-

sitioned in the fireplace but a few inches in front of its 

final location.

3.   Install the side surround panels by lining up the holes in 

the tabs on the side surround panels in front of the holes 

on the surround brackets.  Next insert two slotted 1/4" 

truss screws for each side surround panel and secure 

loosely. 

f

aCe

 i

nstallation

The faces come with hooked brackets. To install the face, 

hang the hooked brackets on the surround brackets (C in 

Figure 12).

Figure 1

A

B

C

Spring Handle Latches

Door Mounting Plates

Front Logs

4.   Fasten top surround panel with the remaining two truss 

screws. Tighten all six truss screws after adjusting the 

surround panels to eliminate space between side and 

top surround panels.

5.   Assemble the surround trim by inserting the elbowed 

retainer in the rectangular slot in the ends of the longest 

piece of trim and secure by tightening the screw in the 

retainer. Slide the mitred ends of the two side trim pieces 

onto the elbowed retainer and secure by tightening the 

retainer screw.

6.   The  fastened  trim  pieces  should  now  be  horseshoe 

shaped. Slide the trim down over the surround panels 

so the edge of the surround panel fits just behind the 

rounded edge of the trim.  

7.   Install three spring clips (found in parts bag in firebox) 

in  each  piece  of  trim  by  inserting  them  between  the 

rear of the surround panel and the channel of the trim. 

The spring clips will push the trim tight to the surround 

panel.

Summary of Contents for Direct-Vent Gas

























Reviews: