background image

8

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

VIS

ALCOVE DIMENSIONS -  DIMENSIONS – ALCOVE

MAXIMUM DEPTH / PROFONDEUR MAXIMUM 35”(889mm)

MINIMUM WIDTH / LARGEUR MAXIMUM 51”(1295mm)

MINIMUM HEIGHT / HAUTEUR MAXIMUM 46”(1168mm)

SEE OWNER’S MANUAL FOR OTHER ALCOVE 

CLEARANCE CONFIGURATIONS.

RÉFÉREZ VOUS AU MANUEL D’INSTALLATION 

POUR TOUT AUTRE DÉGAGEMENT REQUIS.

HEARTH PROTECTION

SEE INSTRUCTION MANUAL.

PROTECTIONS AU PLANCHER : RÉFÉREZ 

VOUS AU MANUEL D’INSTALLATION.

* 16.5” (1295Mm) to sidewall in an alcove 

* Dégagement des matériaux 

  Combustible pour les murs de côté 

  Dans une alcôve est 16.5 Po (1295mm)

  De chaque côté.

MINIMUM CLEARANCES TO COMBUSTIBLES IN INCHES

DÉGAGEMENTS AUX COMBUSTIBLES - POUCES

2"

(51mm)

*15"

(381mm)

Co

m

bu

sti

ble

 W

all

Mur Combustible

VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUEL

MAY BE INSTALLED IN RESIDENTIAL BEDROOMS AND MANUFACTURED (MOBILE) HOMES.

TESTED TO ANSI Z21.88-2005/CSA 2.33-2005 “VENTED GAS FIREPLACE HEATERS”, UL307b, CSA P.4.1-02, AND CGA 2.17-M91.

THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH LOCAL CODES, IF ANY.  IF NOT, FOLLOW THE CURRENT ANSI 

Z223.1/NFPA 54-LATEST EDITION (USA) OR CAN/CGA  B149.1-LATEST EDITION (CANADA)

 AND SAFETY STANDARD, TITLE 24 CFR, 

PART 3280 FOR MOBILE HOMES.  ALSO, APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER’S 

INSTALLATION INSTRUCTIONS.

THIS APPLIANCE IS ONLY FOR USE WITH THE TYPE OF GAS INDICATED ON THE RATING PLATE AND MAY BE INSTALLED IN 

AN AFTERMARKET, PERMANENTLY LOCATED, MANUFACTURED (MOBILE) HOME WHERE NOT PROHIBITED BY LOCAL CODES. 

SEE OWNER’S MANUAL FOR DETAILS. THIS APPLIANCE IS NOT CONVERTIBLE FOR USE WITH OTHER GASES, UNLESS A 

CERTIFIED KIT IS USED.

DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT.

IF ELECTRICALLY CONNECTED, CONNECTIONS AND GROUNDING MUST BE IN ACCORDANCE WITH LOCAL CODES, IF ANY. 

IF NOT, FOLLOW THE CURRENT NATIONAL ELECTRICAL CODE ANSI/NFPA 70-LATEST EDITION (USA) OR CSA C22-1-LATEST 

EDITION (CANADA).

VENTING: THIS APPLIANCE  MUST  BE  PROPERLY  CONNECTED  TO A  VENTING  SYSTEM  IN ACCORDANCE  WITH  THE 

MANUFACTURER’S INSTRUCTIONS. SEE MANUFACTURER’S INSTALLATION INSTRUCTIONS FOR APPROVED PIPE BRANDS 

AND PIPE SEALING PROCEDURES.

FOR ALTITUDES ABOVE 2,000 FT/610M (IN CANADA 4500 FT/1370M) DE-RATE THE APPLIANCE BY FOUR (4)% FOR EVERY 1,000 

FT (405 M).
THIS VENTED GAS FIREPLACE HEATER IS NOT FOR USE WITH AIR FILTERS.

Part No./ No. Pièce #36242 Rev. A, 05/2007

DO NOT REMOVE OR COVER THIS LABEL

MADE IN U.S.A.

CAUTION:

HOT WHILE IN OPERATION. DO NOT TOUCH. SEVERE BURNS MAY RESULT. KEEP 

CHILDREN, CLOTHING, FURNITURE, GASOLINE AND OTHER LIQUIDS HAVING FLAMMABLE VAPORS 

AWAY. KEEP BURNER AND CONTROL COMPARTMENT CLEAN. SEE INSTALLATION AND OPERATING 

INSTRUCTIONS ACCOMPANYING APPLIANCE. FOR USE WITH GLASS DOORS CERTIFIED WITH THIS 

APPLIANCE ONLY. DO NOT OPERATE THE APPLIANCE WITH GLASS REMOVED, CRACKED OR BROKEN. 

REPLACEMENT OF THE PANEL(S) SHOULD BE DONE BY A LICENSED OR QUALIFIED PERSON.
WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN 

CAUSE INJURY OR PROPERTY DAMAGE. REFER TO THE OWNER’S INFORMATION MANUAL PROVIDED 

WITH THIS APPLIANCE. FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED 

INSTALLER, SERVICE AGENCY OR GAS SUPPLIER.

ALCOVE OR PARALLEL / 

POSITION PARALLÈLE OU 

POSITION DE L'ALCÔVE

CORNER / 

POSITION

EN COIN

MANUFACTURED BY / FABRIQUÉ PAR:

LENNOX HEARTH PRODUCTS

PO BOX 987

AUBURN, WA., USA 98071

MODEL

VISION™

MODÈLE

Report No. / Número de Rapport

050-S-16b-5

SERIAL

 NO.

FACTORY EQUIPPED FOR NATURAL GAS. IF CONTROL PANEL CONTRADICTS THIS LABEL, UNIT FUEL TYPE HAS BEEN CONVERTED.

CET APPAREIL EST MUNI D’ÉQUIPEMENT POUR L’USAGE DU GAZ NATUREL. SI L’ÉTIQUETTE DU PANNEAU DES COMMANDES CONTREDIT 

CETTE ÉTIQUETTE, C’EST QUE LE TYPE DE CARBURANT DE CET APPAREIL A ÉTÉ CONVERTI.

RATINGS

Vision 35 (VIS35)

Vision 25 (VIS25)

NATURAL GAS

LP GAS

NATURAL GAS

LP GAS

MAX/MIN INPUT BTUH 0-2,000 FT (0-610 M)*

35,000/23,000

35,000/23,500

25,000/17,500

25,000/18,000

MANIFOLD PRESSURE (IN. WC)

3.5

10.0

3.5

10.0

MIN. INLET PRESSURE (IN. WC)

5.0

11

5.0

11

ORIFICE (DMS) 0-2,000 FT (0-610 M)*

#34/.111 IN.

#50/.070 IN.

#42/.093 IN.

#53/.059 IN.

*UNIT FACTORY EQUIPPED FOR 0-2000 FT/0-610 M, IN CANADA 0-4500 FT/0-1370 M

ELECTRICAL RATING: 120 VAC, 60 HZ, LESS THAN 2 AMPS

DATE OF MANUFACTURE / DATE DE FABRICATION

2007

2009

2010

2008

JANV

JAN

FEVR

FEB

MARS

MAR

AVR

APR

MAI

MAY

JUIN

JUN

JUIL

JUL

AOÛT

AUG

SEPT

SEP

OCT

OCT

NOV

NOV

DEC

DEC

90°

    5-5/8”

(143mm)

10”

(254mm)

10”

(254mm)

8-7/8”

 (225mm)

Co

mb

ust

ible

 Wa

ll

Mur C

omb

ustib

le

HOMOLOGUÉ FOYER RADIANT PRÉFABRIQUÉ AU 

GAZ -NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE

MAY BE INSTALLED IN RESIDENTIAL BEDROOMS AND MANUFACTURED (MOBILE) HOMES.
TESTÉ SELON LA NORME ANSI Z21.88-2005/CSA 2.33-2005 «FOYER RADIANT AU GAZ», UL307B, CSA P.4.1-02, ET CGA 2.17-M91.
CET APPAREIL DOIT ÊTRE INSTALLÉ CONFORMÉMENT AUX EXIGENCES DES CODES RÉGIONAUX ET DU CODE D’INSTALLATION 

ANSI NFPA 54-DERNIÈRE ÉDITION (ETATS-UNIS), OU CAN/CGA-B149.1-DERNIÈRE ÉDITION (CANADA) POUR LES MAISON MOBILE 

LE STANDARD DE SÉCURITÉ EST TITLE 24CFR, PART 3280 .  CET APPAREIL DOIT ÊTRE INSTALLER SELON LES SPÉCIFICATIONS 

DU MANUFACTURIER.
CET APPAREIL DOIT ÊTRE UTILISÉ AVEC LE TYPE DE GAZ INDIQUÉ SUR LA PLAQUE SIGNALÉTIQUE ET PEUT ÊTRE INSTALLÉ 

DANS UNE MAISON PRÉUSINÉE OU DANS UNE MAISON MOBILE FIXE, LÀ OÙ LES CODES RÉGIONAUX LE PERMETTENT. VOIR LE 

MANUEL D’ENTRETIEN POUR PLUS DE DÉTAILS. CET APPAREIL NE PEUT PAS ÊTRE CONVERTI POUR L’USAGE AVEC D’AUTRES 

TYPES DE GAZ À MOINS D’UTILISER UNE TROUSSE DE CONVERSION HOMOLOGUÉE.
DANGER: RISQUE DE CHOC ÉLECTRIQUE. DÉBRANCHEZ L’APPAREIL AVANT D’EN FAIRE L’ENTRETIEN.
SI L’APPAREIL REQUIERT UN BRANCHEMENT ÉLETRIQUE, LES RACCORDEMENTS ET LA MISE À LA TERRE DOIVENT ÉTRE 

CONFORMES AUX EXIGENCES DES CODES RÉGIONAUX ET DU CODE D’INSTALLATION ANSI/NFPA 70 OU CSA C22-1.

CONDUIT:  CET  APPAREIL  DOIT  ÊTRE  INSTALLER  SEULEMENT  AVEC  UN  CONDUIT  D’ÉVACUATION 

RECOMMANDÉ PAR LE MANUFACTURIER.  TOUJOURS SE RÉFÉRER AU MANUEL D’INSTALLATION.
EN ALTITUDE, AU-DELÀ DE 2000 PI/610 M, (AU CANADA 0-4500 PI/0-1370M) LA CAPACITÉ ÉNERGÉTIQUE DE 

L’APPAREIL DIMINUE DE QUATRE (4)% POUR CHAQUE 1000 PI (405 M).
CE FOYER RADIANT AU GAZ À ÉVACUATION N’EST PAS CONÇU POUR ÊTRE UTILISÉ AVEC DES FILTRES À AIR.

DANGER:

CET APPAREIL DÉGAGE DES TEMPÉRATURES ÉLEVÉES ET DEVRAIT ÊTRE 

INSTALLÉ À L’ÉCART DES ENDROITS TRÈS PASSANTS ET LOIN DES MEUBLES ET RIDEAUX. 

SURVEILLEZ LES ENFANTS QUI SE TROUVENT DANS LA PIÈCE. GARDEZ LA ZONE AUTOUR DU 

FOYER EXEMPTE DE MATÉRIAUX COMBUSTIBLES, D’ESSENCE ET AUTRES VAPEURS ET LIQUIDES 

INFLAMMABLES. MAINTENEZ LE BRÛLEUR ET LE BOÎTIER DES COMMANDES PROPRE EN TOUT 

TEMPS. VOIR LES MANUELS D’INSTALLATION ET D’ENTRETIEN QUI ACCOMPAGNENT L’APPAREIL. 

SEUL LE PANNEAU VITRÉ FOURNI PAR LE MANUFACTURIER PEUT ÊTRE UTILISÉ AVEC CET APPAREIL. 

EN AUCUN CAS, L’APPAREIL NE PEUT ÊTRE UTILISÉ SANS LA VITRE OU AVEC LA VITRE BRISÉE. LE 

REMPLACEMENT DE LA VITRE DOIT ÊTRE EFFECTUÉ PAR UN TECHNICIEN DE SERVICE QUALIFIÉ.
AVERTISSEMENT: UNE  INSTALLATION  INADÉQUATE  DE  MÊME  QU’UN  AJUSTEMENT,  UNE 

MODIFICATION,  UNE  RÉPARATION  OU  UN  ENTRETIEN  INCORRECTS  PEUVENT  CAUSER  DES 

BLESSURES OU DOMMAGES À LA PROPRIÉTÉ. RÉFÉREZ-VOUS AU MANUEL D’ENTRETIEN LIVRÉ AVEC 

CET APPAREIL. POUR DE L’ASSISTANCE, CONSULTEZ UN INSTALLATEUR QUALIFIÉ, UNE ENTREPRISE 

DE SERVICE OU UN FOURNISSEUR DE GAZ.

SPÉCIFICATIONS

Vision 35 (VIS35)

Vision 25 (VIS25)

GAZ NATUREL

GAZ PROPANE

GAZ NATUREL

GAZ PROPANE

ENTRÉE MAX/MIN BTU/HR 0-4500 pi (0-1370 

M)*

35000/23000 35000/23500 25000/17500

25000/18000

PRESSION À LA SORTIE  (IN. WC/C.E.)

3.5

10.0

3.5

10.0

PRESSION MINIMUM D’ENTRÉE DU GAZ 

(IN. WC/C.E.)

5.0

11

5.0

11

ORIFICE (DMS) 0-4500 pi (0-1370 M)*

#34/.111"

#50/.070"

#42/.093"

#53/.059"

* L’APPAREIL PRÉUSINÉ EST MUNI D’ÉQUIPEMENT POUR 0-2000 PIEDS (0-610 M). AU CANADA 0-4500 PIEDS (0-1370M).

SPÉCIFICATIONS ÉLECTRIQUE 120 VCA, 60 HZ, MOINS DE 2 AMPÈRES 

NE PAS RETIRER CETTE ÉTIQUETTE        

Fabriqué aux  U.S.A.

IGN

Poêle

Poêle

Stove

Stove

Safety / Listing Label

Summary of Contents for Gas Stove































Reviews: