background image

9

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Pl

an

ni

ng

 In

st

al

la

tio

n

Sa

fe

ty

 a

nd

 G

en

er

al

In

st

al

la

tio

n

Op

er

at

io

n

M

ai

nt

en

an

ce

Tr

ou

bl

es

ho

ot

in

g

Pa

rts

 / 

Ac

ce

ss

or

ie

s

SPECIFICATIONS - GRANDVIEW™ 230

Stove Pipe Diameter

Single Wall or Double Wall 

6” (152 mm)

Log Length   

 

16” W x 18” D  Max. 

 

 

(406mm W x 457mm D  Max.)

Firebox   

 

17” W x 19” D x 12-1/2” H  Max. 

 

 

(432mm W x 483mm D x 318mm  

 

 

H Max.) Volume = 2.3 cu. ft.

Glass Viewing Area 

 

16-1/2” W x 11-5/16” H

 

 

(419mm W x 287mm H)

EPA Test Load:  

 

28,200 BTUs/hr.

Cord Wood: 

u

 

 

76,000 BTUs/hr.

Maximum Burn Times 

u

   

12 hours

Heating Capacity 

u

   

 

 1200 to 2200 sq. ft.

EPA Grams Per Hour  

 

 3.6 gr/hr

EPA Phase II and Washington State Approved

Product Reference Information

Cat. No.

Description

Ship. 

Weight

Ship.

 Volume

H8338

Grandview 230 Wood-Burning Stove

385 lb.

20.09 cu. ft.

Pedestal

35”

(889mm)

Specifications

The Grandview™ Model GV230 woodstove 

is safety listed with the following agency:

•  Intertek, Tested to UL 1482, ULC S627

Listing

Dimensions

Notes:

 

•    Dimensions shown are approximations only (+/- 1/4”)

•   Diagrams, illustrations and photographs are not to scale – consult installa-

tion instructions. Product designs, materials, dimensions, specifications, 
colors and prices are subject to change or discontinuance without notice.

•   

Approved for residential, manufactured home, and alcove installations.

•   

Optional Kits Available:

  Door Trim Kit
  Blower
  Outside Air Kit
  Louvers
  Legs (choice of three styles)
  Pedestal
  Ash Drawer for legs or for pedestal

u

 

Square-foot heating capacities and burn times are approximations only.  
Actual performance may vary depending upon home design and insula-
tion, ceiling heights, climate, condition and type of wood used, appliance 
location, burn rate, accessories chosen, chimney installation and how the 
appliance is operated.

16-1/2”

(419mm)

11-5/16”

(287mm)

23-3/4”

(603mm)

21-5/16”

(541mm)

1”

(25mm)

6-9/16”

(167mm)

24-3/4”

(629mm)

26-5/8”

(676mm)

25-1/8”

(638mm)

6”

(152mm)

Figure 5

            Legs

Olympic 33-1/2” (851mm)
Coastal 32-1/2” (826mm)
Lakeview 32-13/16” (833mm)

23-1/8”

(587mm)

Pl

an

ni

ng

 In

st

al

la

tio

n

WIN # 20551

Summary of Contents for Grandview GV230

































Reviews: