background image

4

LENNOX HEARTH PRODUCTS  •  MERIT PLUS

®

 B-VENT GAS FIREPLACES (MPB33/35/40/45)  •  CARE AND OPERATION INSTRUCTIONS

4

Important Safety Information

1. WARNING: Do not operate appliance with the glass front 

removed, cracked or broken. 

2. Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician to inspect the 
appliance and to replace any part of the control system and 
any gas control which has been under water.

3. Due to high temperatures, the appliance should be located 

out of traffic and away from furniture and draperies.

4. Children and adults should be alerted to the hazards of high 

surface temperature and should stay away to avoid burns or 
clothing ignition. 

5. Clothing or other flammable material should not be placed 

on or near the appliance.

6. Young children should be carefully supervised when they 

are in the same room as the appliance. Toddlers, young 
children, and others may be susceptible to accidental contact 
burns. A physical barrier is recommended if there are at-risk 
individuals in the house. To restrict access to a fireplace or 
stove, install an adjustable safety gate to keep toddlers, 
young children, and other at-risk individuals out of the room 
and away from hot surfaces.

7. Any safety screen or guard removed for servicing an 

appliance must be replaced prior to operating the appliance.

8. Installation and repair should be done by a qualified service 

person. The appliance should be inspected before use and 
at least annually by a professional service person. More 
frequent cleaning may be required due to excessive lint 
from carpeting, bedding material, et cetera. It is imperative 
that control compartments, burners, and circulating 
air passageways of the appliance be kept clean. See 
maintenance instructions on 

Page 11

.

L’information de sûreté importante

1.  AVERTISSEMENT. Ne pas utiliser l’appareil si le panneau frontal en 

verre n’est pas en place, est craqué ou brisé.

2.  Ne pas utiliser cet appareil s’il a été plongé, même partiellement, 

dans l’eau. Appeler un technicien qualifié pour inspecter l’appareil 

et remplacer toute partie du système de commande  

3.  et toute commande qui a été plongée dans l’eau.
4.  En raison des températures élevées, l’appareil devrait être installé 

dans un endroit où il y a peu de circulation et loin du mobilier et 

des tentures.

5.  Les enfants et les adultes devraient être informés des dangers que 

posent les températures de surface élevées et se tenir à distance 

afin d’éviter des brûlures ou que leurs vêtements ne s’enflamment.

6.  On ne devrait pas placer de vêtements ni d’autres matières 

inflammables sur l’appareil ni à proximité.

7.  Les jeunes enfants devraient être surveillés étroitement lorsqu’ils 

se trouvent dans la même pièce que l’appareil. Les tout petits, 

les jeunes enfants ou les adultes peuvent subir des brûlures s’ils 

viennent en contact avec la surface chaude. Il est recommandé 

d’installer une barrière physique si des personnes à risques habitent 

la maison. Pour empêcher l’accès à un foyer ou à un poêle, installez 

une barrière de sécurité ; cette mesure empêchera les tout petits, 

les jeunes enfants et toute autre personne à risque d’avoir accès à 

la pièce et aux surfaces chaudes.

8.  Tout écran ou protecteur retiré pour permettre l’entretien de l’appareil 

doit être remis en place avant de mettre l’appareil en marche.

9.  L’installation et la réparation devrait être confiées à un technicien 

qualifié. L’appareil devrait faire l’objet d’une inspection par un 

technicien professionnel avant d’être utilisé et au moins une fois l’an 

par la suite. Des nettoyages plus fréquents peuvent être nécessaires 

si les tapis, la literie, et cetera produisent une quantité importante 

de poussière. Il est essentiel que les compartiments abritant les 

commandes, les brûleurs et les conduits de circulation d’air de 

l’appareil soient tenus propres. Voyez les instructions d’entretien 

à la 

Page 11

.

[SPANISH]

Información importante de seguridad

1.  ADVERTENCIA: No opere el artefacto con el frente de vidrio quitado, 

agrietado o roto.

2.  No use este artefacto si alguna de sus partes ha estado bajo agua. 

Llame de inmediato a un técnico de servicio calificado para que 

inspeccione el artefacto y reemplace cualquier parte del sistema  

3.  de control y cualquier control de gas que haya estado bajo agua.
4.  Debido a las altas temperaturas, el artefacto debe situarse fuera  
5.  de las áreas de tráfico y lejos del mobiliario y cortinas.
6.  Se debe alertar a los niños y adultos sobre los peligros de  
7.  las altas temperaturas en la superficie y que se mantengan  
8.  alejados para evitar quemaduras o ignición de la ropa. 
9.  No debe colocarse ropa u otros materiales inflamables  
10. sobre y cerca del artefacto.

11. Se debe supervisar de cerca a los niños cuando estén en el mismo 

cuarto que el artefacto. Los niños pequeños, los jóvenes y otras 

personas pueden ser susceptibles a quemaduras por contacto 

accidental. Se recomienda instalar una barrera física si hay personas 

en riesgo en la casa. Para restringir el acceso a una chimenea o estufa, 

instale una puerta de seguridad ajustable  

12. para mantener a los niños pequeños, jóvenes y otras personas  
13. en riesgo fuera del cuarto y lejos de las superficies calientes.
14. Cualquier malla o resguardo de seguridad quitado para dar servicio a 

un artefacto, debe reinstalarse antes de operar el artefacto.

15. Una persona de servicio competente debe realizar la instalación y 

reparación. Una persona de servicio profesional debe inspeccionar 

el artefacto antes de usar al menos una vez por año. Se puede 

requerir limpieza más frecuente debido a la pelusa excesiva del 

alfombrado, del material de cobijas, etc. Es imprescindible mantener 

limpios los compartimientos de control, los quemadores y los 

pasajes de circulación del aire del artefacto. Ver las instrucciones de 

mantenimiento en la 

Página 11

.

Summary of Contents for MPB-35

































Reviews: