background image

0650329-56 / 506265-03

Issue 1924

Page 1 of 13

Save these instructions for future reference

INSTALLATION INSTRUCTIONS

EFV Electric Furnace

Warm Air Unit

 

(P) 506265-03

*P506265-03*

Manufactured By

Allied Air Enterprises LLC

A Lennox International, Inc. Company

215 Metropolitan Drive

West Columbia, SC 29170 

This manual must be left with the homeowner for future reference.

This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in 

manuals, be alert to the potential for personal injury or death.

Table of Contents

Installation ...................................................................2

Condensate Drain Connection ....................................4

Electrical Wiring ...........................................................5

Setup ...........................................................................6

Sequence of Operation................................................8

System Check .............................................................9

Replacement Parts ....................................................10

Maintenance ..............................................................10

Airflow Configurations

................................................11

Improper installation, adjustment, service, or 

maintenance can cause injury or property damage. 

Refer to this manual. For assistance or additional 

information,  consult  a  qualified  installer  or  service 

agency.

 WARNING

The information contained in this manual is intended 

for  use  by  qualified  service  technicians  familiar  with 

safety procedures and equipped with the proper tools 

and test instruments. Failure to carefully read and follow 

all instructions in this manual can result in equipment 

malfunction, property damage, personal injury, and/or 

death.

 WARNING

Disconnect  all  power  supplies  to  both  the  indoor 

blower section and outdoor section before making any 

electrical connections or servicing the system. More 

than  one  disconnect  switch  may  be  required  to  de-

energize the equipment. Hazardous voltage can cause 

severe personal injury or death.

 WARNING

Inspection of Shipment

Upon receipt of equipment, carefully inspect it for possible 

shipping damage. If damage is found, it should be noted 

on the carrier’s freight bill. Take special care to examine 

the unit inside the carton if the carton is damaged. Any 

concealed damage discovered should be reported to the 

last carrier immediately, preferably in writing, and should 

include a request for inspection by the carrier’s agent.

If any damages are discovered and reported to the carrier 

DO NOT INSTALL THE UNIT

, as claim may be denied.

Check the unit rating plate to confirm specifications are as 

ordered.

Summary of Contents for Allied Air EFV Series














Reviews: