background image

0650329-56 / 506265-03

Issue 1924

Page 10 of 13

Replacement Parts

Use only original equipment service parts when repairing 

these products. These parts include but are not limited 

to: circuit breakers, heater controls, heater limit controls, 

heater elements, motor, blower relay, control transformer, 

blower wheel, indoor coil, and sheet metal parts.

When ordering replacement parts, it is necessary to order 

by part number and include with the order the complete 

model number and serial number (see unit data plate). 

Refer to the parts list for unit component part numbers.

Maintenance

Air Filters

Do not operate system without a filter. A filter is required 

to  protect  the  coil,  blower,  and  internal  parts  from 

excessive dirt and dust.

 IMPORTANT

See unit position figures for location of filter in unit cabinet 

and service panel giving access to unit filter.

Inspect  air  filters  at  least  once  a  month  and  replace  or 

clean as required. Dirty filters are the most common cause 

of inadequate heating or cooling performance. Replace 

disposable  filters.  Washable  filters  can  be  cleaned  by 

soaking  in  mild  detergent  and  rinsing  with  cold  water. 

Install new/clean filters with the arrows on the side pointing 

in the direction of airflow.

Never  replace  a  washable  (high  velocity)  filter  with  a 

disposable (low velocity) filter unless return air system is 

properly sized for it.

Owner Record

Furnace Model #

Serial #

Installation Date:

Installed By:

Dealer:

Address:

Telephone #

License #

Contact Person:

Other Equipment Installed:

Equipment Type:

Model #

Serial #

Installation Date:

Equipment Type:

Model #

Serial #

Installation Date:

Equipment Type:

Model #

Serial #

Installation Date:

Summary of Contents for Allied Air EFV Series














Reviews: